Bedienungsanleitung Remington HC4255 (Seite 6 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch, Alle Sprachen)

719577

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

CARE FOR YOUR HAIRCLIPPER

• To ensure long lasting performance of your clipper, clean the blades and unit regularly.

• Always keep the clipper in the provided travel pouch.

• Ensure the appliance is switched o and unplugged from the mains before cleaning.

• Do not use harsh or corrosive cleaners on the unit or blades.

• Cleaning should be done with a soft brush.

• After each use - brush the accumulated hair from the blades.

WASHABLE CLEANING

• The QuickCut Clipper is fully washable for easy cleaning.

• Ensure the appliance is switched o and unplugged from the mains.

WASHOUT PORT INSTRUCTIONS

Note: Never rinse, wash or otherwise subject this product to liquid whilst the power cord is connected.

• For best results, keep trimmer running while running it under the tap. Allow water to run through the

washout port and over the blades. Recommended to rinse after each use.

• Ensure the clipper is dry after cleaning.

• For more thorough cleaning the blade set can be easily removed to wash any hair trimmings from the

blades. To release the blade set, push the blade set release button found on the base of the clipper.

• Ensure the blades are dry after rinsing under the tap. To reattach, align the blade set onto the clipper

and push the blade set towards the clipper body until it clicks into place.

• Place a small drop of cutter or sewing machine oil onto the blades at each end and at the middle point of

the blades. Turn the unit on for a few seconds to distribute the oil then turn o and wipe o excess oil.

BATTERY REMOVAL

• The battery must be removed from the appliance before it is scrapped.

• The appliance must be disconnected from the supply mains when removing the battery.

• Ensure the clipper is discharged of all power.

• Starting at the seam on either side of the charge indicator lens, pry open seam working back and forth

from one side to the other, following the seam until the top shell has been pried apart all the way from

the rest of the clipper. Remove the two screws from the inner housing.

• Gently pull the inner housing straight up and away to remove the inner housing shell.

• Remove the two screws from the inner structure located on each side of the circuit board.

• Gently pull the inner structure containing the battery and circuit board up out of the lower housing

structure of the clipper.

• From the under side of this inner structure, cut the red and black wires which lead to the battery.

• With the inner housing structure right side up, pull upward rmly on the circuit board to allow room

to remove the battery. Pry the battery out of its holder.

• Dispose of the batteries safely.

RECYCLING

To avoid environmental and health problems due to hazardous substances,

appliances and rechargeable and non-rechargeable batteries marked with one of

these symbols must not be disposed of with unsorted municipal waste. Always

dispose of electrical and electronic products and, where applicable, rechargeable

and non-rechargeable batteries, at an appropriate ocial recycling/collection point.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remington HC4255 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info