587581
18
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
Minimum clearances
Observe the minimum clearances
to allow access for maintenance
and repair work and facilitate
optimum air distribution.
Connection options
The following connection options
are available for the condensation
pipes and control cables.
Connection options
4
1 Exit on wall, right
2 Exit through wall, right
3 Exit through wall, left
4 Exit on wall, left
Rear view
1
2 3
Minimum clearances
All values in mm
1000
1000
1000
1000
300
Important points prior to
installation
When installing a complete
system, take into account the
manuals for the indoor unit and
outdoor component.
Transport the unit in its original
packaging as close as possible
to the installation location.This
avoids transportation damage.
Check that the packaged
contents are complete and
inspect the unit for any visible
signs of transportation damage.
Immediately notify any
deficiencies to the contractual
partner and forwarding agent.
Lift the unit by its corners
and not the refrigerant or
condensation connections.
Insulate the refrigerant pipes
(injection and suction pipe),
valves and connections to make
them tight against vapour
diffusion. If necessary, also
insulate the condensation pipe.
Select an installation location
which allows air to freely flow
through the inlet and outlet
(see section "Minimum
clearances").
Do not install the unit
adjacent to any hotspots. Unit
performance will be impaired if
installed next to hotspots.
Installation material
The indoor unit is fastened by the
back of its housing using 4 screws
to be provided by the customer.
Selecting the installation
location
The indoor unit is designed for
horizontal wall-mounting high up
on walls (min. 1.75 m above the
level of the floor).
Installation instructions for qualified personnel
Use caps or adhesive tape to
seal off the open refrigerant
pipes and prevent the ingress of
humidity. Never kink or push in
the refrigerant pipes.
Only use the union nuts
supplied with the refrigerant
pipes. These should only
be removed shortly before
connecting the refrigerant
pipes.
Establish all electrical
connections in accordance with
the relevant DIN- and VDE
standards.
Ensure the electrical cables
are properly connected to the
terminals,
otherwise there is a risk of fire.
REMKO ATY
18
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO ATY351 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO ATY351

REMKO ATY351 Zusatzinformation - Deutsch - 1 seiten

REMKO ATY351 Bedienungsanleitung - Deutsch - 28 seiten

REMKO ATY351 Bedienungsanleitung - Holländisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info