Bedienungsanleitung REMKO ETF360 (Seite 9 von 20) (Englisch)

587878

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Electrical wiring

■

The units are operated with

230 V 50 Hz alternating current

■

The electrical

connection is made

using a built-in

mains cable with

earthed safety plug

■

Extensions to the connection

cable may only be carried out

by authorised electricians,

subject to the length of

the cable, connected load

of the unit and taking into

consideration how the unit is

used at its location

Control panel

All rotary knobs and the

corresponding indicator lights are

located on the control panel.





  

    

 “Container full” display

 “Hot gas defrosting” display

 “Timer activated” display

 Display for temperature

indication and timer setting

 Display to show and adjust the

relative humidity

 “Power ON/OFF” key

 Key for fan speed

 Key for “1 to 24 hrs” timer

(in 1 hour steps)

 Key to adjust the hygrostat

from 30 to 90 % RH in 5 %

steps

 Changeover button to display

in °C or °F

Switching the units on

■

Connect the unit's power plug

to a properly installed mains

socket

■

Press the power key []

■

Use the [] key to select the

(min/max) air volume

The electrical connection to the units

must be made at feed-points with

residual current devices in accordance

with VDE 0100, Section 704.

When installing the units in

extremely damp environments such

as laundry rooms, showers etc., the

unit must secured with a residual

current device provided by the

customer in accordance with the

regulations.

NOTE

In room temperatures

below

10 °C

and relative

humidity below

40 %

economical use of the unit can

no longer be guaranteed.

NOTE

When the units are connected

to the power supply, they beep

quickly and the displays ﬂash

once.

NOTE

Adjusting the humidity level

The unit’s dehumidiﬁcation power

is entirely dependent on the

conditions inside the room, the

room temperature, the relative

humidity and observance of the

notes in the “Set-up” chapter.

The higher the room temperature

and relative air humidity, the

higher the dehumidiﬁcation power.

A relative humidity of around

45 to 60 % is recommended for

living rooms.

However, the air humidity

should not exceed 40 to 45 % in

warehouses, archives, etc.

Unit initial settings:

Fan speed = min.

Humidity = 60 % RH

■

Use the [] buttons to select

the required humidity (% RH)

The set value is shown on

the display [] for around

10 seconds

■

The humidity level can be

adjusted in 5 % steps

from 30 - 90 % RH

■

In normal operating mode, the

display [] shows the current

humidity level in % RH

■

The display [] shows the

current room temperature

in °C or °F

The display is changed over

using the [] key

All cable extensions must only

be used in fully un-reeled or

reeled off condition.

CAUTION

The units are only permitted

to be operated with the outlet

grill clear in order to prevent

overheating.

CAUTION

NOTE

At a humidity of < 30 %,

the “LO” indicator is shown

and, at > 90 %, the “HI” is

shown on the display [

]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO ETF360 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO ETF360

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info