Bedienungsanleitung REMKO GPM 15 (Seite 10 von 44) (Englisch)

587905

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

REMKO GPM

Room correction

For this function, use of the

temperature control ATR.6 is

necessary.

A type of function is described

in the following that enables

maximum energy efﬁciency to

be achieved by the hot air heater

assisted by the control electronics

and temperature control.

In order to activate the ambient

correction function, the parameter

[C1]

param k 11 must be set to 1.

The purpose of the room

correction function is to ensure

rapid heating at the beginning and

subsequently maintain the room

temperature at a constant level.

In this way, not only can layer

formation in the room air be

reduced, but also the fuel demand

reduced in particular.

The two correction reference

values are the temperature

measured by the sensor NTC2

(in the temperature control) and

the circulation air temperature

measured by the sensor NTC1 (at

the unit).

To activate the function, set the

parameter

param k 17 to 1.

When the room temperature

approaches the setpoint value,

the modulation temperature is

changed linearly based on the two

parameters A16 and A24.

This makes it possible to operate

the unit on heat demand

at maximum output and to

quickly reach the preset room

temperature.

The heat output is subsequently

reduced which increases the

efﬁciency of the unit and the room

is heated with less hot air.

This enables the layer formation in

the room air and simultaneously

the heat loss to be reduced.

The units are supplied with the

following factory settings:

Modulation temperature:

„REG SAN“ 22°C

Neutral correction range:

A24 2°C

Correction coefﬁcient:

A16 2

The parameter A24 determines

the range within which the

room temperature is corrected.

The parameter A16 offers the

possibility to increase the efﬁciency

of the temperature reduction

to the setpoint “REG SAN” as

shown on the graph. At the

standard setting, the modulation

temperature on reaching the room

temperature corresponds to:

„REG SAN“ =

24°C-(2°C x 2.5) = 19°C

The correction is independent of

the set room temperature.

The graph shows the room

temperatures [ST2] in relation

to the installation height of the

units „REG SAN“ during the initial

heating phase.

To deactivate the correction, set

the parameter [C1]

param k 11 to

When deactivating the correction,

the value “REG SAN” must be

correctly regulated in order to

avoid the following conditions:

- „REG SAN“ adjusted too high:

Strong layer formation with

high heat loss in roof area and

increased energy demand as a

consequence.

„REG SAN“ adjusted too low:

Time to reach the required room

temperature too long.

With correction deactivated, adjust

“REG SAN” so that the value is

higher than ST2 by the difference

in metres between the room and

modulation sensor multiplied by

0.4/0.5°C.

To change the modulation value

“REG SAN” on the temperature

control and to change all speciﬁed

values, see further back in the

manual.

Raumtemperatur

Modulationstemperatur

ST1

ST2

A24

A24 x A16

ST1 Korrektur

ST1

ST2

0,5h 1h 1,5h 2h 2,5h 3h

Modulation temperature

Room temperature

ST1 correction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO GPM 15 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO GPM 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info