Bedienungsanleitung REMKO GPM 15 (Seite 11 von 44) (Englisch)

587905

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

The faults indicated and stored by

the control board (interlocks) have

the following causes:

- Fault of the ﬂ ame monitoring

device due to burner ignition

failure; the control board

makes several automatic reset

attempts prior to signalling

the fault.

- Operation of the safety

thermostat.

If the temperature detected

by the thermostat is too high,

the same operates and blocks

operation of the unit.

- Burner fan faulty; the

combustion air fan is faulty or

the signal to the control board

is outside the tolerance range

with respect to the requested

speed.

- NTC1 sensor faulty or not

connected – the sensor value

is outside the measuring

range.

- Control board fault due

to constant and repeated

unsuccessful ignition attempts

of the unit for a predeﬁ ned

period.

With this fault, the fault

signalling LED located on the

control board also lights up.

- The control board sent the

starting signal to the ﬂ ame

monitoring device, but did

not receive the started signal;

it is possible that the ﬂ ame

monitoring device is faulty.

The faults F1 and F2 are caused by

safety devices and are therefore

permanent.

The fault still remains after

switching the mains off and

on again and can only be reset

manually.

The faults F3, F6 and F8 must be

reset manually or by switching the

mains off and on again.

In contrast, fault F4 is self-

resetting:

After clearing the fault, reset takes

place automatically.

The safety information on the

previous pages must be strictly

observed.

In exceptional circumstances, the

units can also be operated brieﬂ y

without temperature control.

For this purpose, the jumper on

terminals 7+9 on the terminal

strip M1 in the switchbox must be

removed and a switching device

(e.g. thermostat) connected.

The CR switch on the control

board must be set to OFF (see Fig.

on page 14) and the connector CN

with resistor (see Fig. on page 26)

plugged in.

For this mode, it is neces-

sary to connect at least one

switching device, e.g. room

thermostat in order to be able

to switch the burner on and

off.

NOTE

All information relating to the unit

and faults are now indicated via

LED indicators on the front of the

unit.

The green LED lights up to indicate

that the unit is connected to the

mains.

The red LED lights up to indicate a

fault on the unit.

The cause of the fault can

immediately be identiﬁ ed by the

different ﬂ ashing/illuminating

states of the red LED:

- LED shows a steady light

- LED ﬂ ashes twice rapidly

- LED ﬂ ashes three times

rapidly

- LED ﬂ ashes four times rapidly

- LED ﬂ ashes constantly

- Red and green LED ﬂ ash

alternately

General information Types of faults

Reset button

A manually operated reset button

on the front of the unit enables

the unit to be reset following faults

F1, F2 or F8 when the temperature

control ATR-6 is not present.

Changeover switch

 Summer / d Winter

Reset button

Green LED

Red LED

Summer/winter switch

A manually operated changeover

switch

d / 0 /  on the front

of the unit allows switching

from winter operation

d to

summer operation

 (continuous

ventilation).

In the middle position [0], all

functions of the unit are switched

off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO GPM 15 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO GPM 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info