Bedienungsanleitung REMKO GPM 15 (Seite 29 von 44) (Englisch)

587905

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Commissioning must be carried

out only by an authorised

installation company or factory

customer service engineers.

The following steps must be

carried out prior to commissioning:

1. Check all connections and

unions of the unit and gas

connection for tightness.

2. Check all accessible electrical

screw-type and plug connectors.

3. Check the electrical connection

for polarity and the mains

supply (230V/50Hz).

4. Check that the unit is

professionally connected to an

effective earthing system in

accordance with the applicable

safety standards.

Only when this is provided,

is electrical safety and reliable

function of the unit ensured.

5. Check that the electronic

temperature control ATR-6 is

correctly connected.

The units are delivered preset

at the factory depending on the

required type of gas.

The complete unit must be

checked for correct functioning

and tightness of all gas

connections.

ATTENTION

Gas pipes must never be

used for earthing electrical

equipment!

Commissioning

It must be ensured that a gas

supply pressure conforming to

standards is constantly available

depending on the type of gas

available locally.

The supplied gas must correspond

to the gas category set on the unit.

The procedure for commissioning

the burner is as follows:

1. Loosen the screwed cap in the

pressure measuring connection

of the burner.

Do not unscrew fully!

2. Connect a suitable pressure

gauge, e.g. U-tube manometer,

minimum resolution 0.1 mbar.

3. Open the gas shut-off devices.

4. Switch on the main/emergency

switch.

5. Adjust the room temperature

setting on the temperature

control ATR-6 to a higher

value than the existing room

temperature.

6. Set the mode selector switch

on the front of the unit to the

position “Heat”.

7. Set the temperature control to

“MANUAL MODE”.

8. Check that the heating symbol

lights up on the temperature

control display.

9. Adjust the heat demand

temperature higher than the

temperature measured by the

room thermostat or temperature

control.

A small ﬂ ame lighting up on the

display shows that the burner is

switched on.

It is possible that the ignition

burner does not ignite ﬁ rst time

due to the presence of air in the

gas pipe, so that the unit generates

a fault.

The unit must be reset and the

starting procedure repeated.

Only authorised specialists

may make adjustments and

carry out maintenance work on

the unit and gas burner.

ATTENTION

Combustion analysis

Start the burner and after

switching on the fan bring the

burner to “maximum output” by

pressing and holding the reset

button on the front of the unit for

2 to 3 seconds.

Operation at maximum output is

indicated by the green LED on the

front of the unit ﬂ ashing once.

Ensure that the gas pressure

upstream of the gas valve

corresponds to the prescribed

value, otherwise regulate.

After about two minutes, connect

a gas analyser to the chimney pipe

and read off the CO2 value.

Compare this value with the values

in the “Gas settings“ table for the

type of gas used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO GPM 15 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO GPM 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info