Bedienungsanleitung REMKO GPM 55 (Seite 33 von 44) (Englisch)

587908

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

For replacing the control board,

several checks must be carried out

and parameters adjusted.

The parameters A1, A2 and

A3 must be adjusted as the

replacement control boards are

supplied neutral.

Every wall gas heater is provided

with a corresponding technical

description with the factory pre-

programmed default values.

This list must be updated with

any locally adapted changes

in order that the replacement

control board can be appropriately

reprogrammed as required.

Checking the control board

hardware conﬁ guration

Check for operation with

temperature control ATR-6:

The jumper NTC/VAN must be on

NTC and the CR switch must be

ON, see diagram below [towards

the inside edge of the board].

This conﬁ guration is necessary to

ensure the correct function of the

NTC sensor.

Jumper on NTC

CR switch

Parameter programming

Programming takes place

exclusively via the temperature

control ATR-6.

The parameters that must be

programmed are:

A1, A2 and A3.

These determine correct

combustion and heat output of the

installed wall heater.

The parameters A1, A2 and A3

are not pre-programmed on

replacement boards.

The values to be adjusted

depending on the particular model

are shown in the table below.

Control board replacement

Model A1 A2 A3

GPM15 44 58 83

GPM25 55 73 83

GPM35 62 93 80

GPM55 65 93 70

GPM75 75 98 70

In order to access the parameters,

press and hold the KM button for

about 10 seconds.

The following appears on the

display:

INFO REG ERR >>

Press the K4 >> button, the

following appears on the display:

SPRA PAR PARK >>

Press the K3 PARK button, the

following appears on the display:

PARAM K 1 >>

The set parameter value 1 appears

above the K4 button and can

be adjusted with the K+ and K-

buttons.

By pressing the K4 >> button,

the parameters from 1 to 3 are

displayed in succession and can

be adjusted with the K+ und K-

buttons.

Chimney sweep button

Set the room temperature (if

necessary) at the temperature

control higher than the actual

room temperature. Wait until the

burner has started.

After switching on the fan, bring

the burner to “maximum output”

by pressing and holding the reset

button on the front of the unit for

2 to 3 seconds.

Operating at maximum output

is indicated by the green LED

ﬂ ashing rapidly.

After about two minutes, exhaust

gas analysis can be carried out

at the measuring point in the

chimney pipe.

After carrying out the

measurement, set the unit to

“normal” mode by pressing and

holding the reset button again for

2 to 3 seconds.

The green LED ﬂ ashes slowly (min.

output).

Press the reset button again and

the green LED shows a steady light

again.

The normal mode is active again.

Set the room temperature (if it has

changed) to the original value.

If the unit is not set to

“normal mode“, the control

board will automatically

reset the unit after 20

minutes.

NOTE

We reserve the right to make changes to dimensions and design in the interest of technological advances.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO GPM 55 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO GPM 55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info