Bedienungsanleitung REMKO GPM 55 (Seite 34 von 44) (Englisch)

587908

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

REMKO GPM

Unit without temperature control

For replacing the gas valve, the

CO2 and if necessary the offset

value must be adjusted.

- Start the burner and after swit-

ching on the fan bring the burner

to “maximum output” by pres-

sing and holding the reset button

on the rear of the unit for 2 to 3

seconds.

Operation at maximum output is

indicated by the green LED on the

front of the unit ﬂashing once.

After about two minutes, connect

a gas analyser and read off the

CO2 value.

Compare this value with the values

in the “Gas settings” table for the

type of gas used.

- If the value is outside the spe-

ciﬁed range, it can be corrected

with the CO2 regulating screw

on the Venturi tube:

The gas ﬂow rate and accordingly

the CO2 value decrease when the

screw is tightened.

The CO2 value increases when the

screw is unscrewed.

Subsequently set the burner to

“minimum output” by pressing

and holding the reset button again

for 2 to 3 seconds.

Operation at “minimum output” is

indicated by the green LED rapidly

ﬂashing twice.

- Wait until the minimum out-

put at the burner has stabilised

and check that the CO2 value

is equal to or slightly below the

CO2 value at the maximum ﬂow

rate ( up to -0.3%).

A deviating value can be corrected

with the offset screw.

To make changes to values, un-

screw the metal plug and turn the

regulating screw:

The CO2 value decreases when

the screw is unscrewed.

The CO2 value increases when the

screw is tightened.

After making any adjustments with

the offset regulating screw, the

CO2 value at maximum output

must be rechecked by carrying out

the above described steps.

After carrying out these steps, set

the unit to “normal” mode by

pressing and holding the reset but-

ton again for 2 to 3 seconds.

This mode is indicated by the

green LED showing a steady light.

This also occurs when the mains

supply to the unit is disconnected

and reconnected.

Unit with temperature control

For replacing the gas valve, the

CO2 and if necessary the offset

value must be adjusted.

- Adjust the regulating parameters

of the sensor NTC1 (“REG SAN”

on the temperature control) to

a value that is higher than the

value measured by the sensor

NTC1 (“FLOW VL” on the tem-

perature control).

- Switch on the burner.

The burner will reach maximum

output after about two minutes

after starting.

Connect an exhaust gas analy-

ser and read off the CO2 value.

Compare this value with the “gas

settings” (page 32) for the type of

gas used.

- If the value is outside the spe-

ciﬁed range, it can be corrected

with the CO2 regulating screw

on the Venturi tube.

The gas ﬂow rate and accordingly

the CO2 value decrease when the

screw is tightened.

The CO2 value increases when the

screw is unscrewed.

Subsequently set the burner to

minimum output by adjusting the

REG SAN value to a value that is

lower than the measured tempe-

rature.

- Wait until the minimum out-

put at the burner has stabilised

and check that the CO2 value

is equal to or slightly below the

CO2 value at the maximum ﬂow

rate ( up to -0.3%).

A deviating value can be corrected

with the offset screw.

To make changes to values, un-

screw the metal plug and turn the

regulating screw:

The CO2 value decreases when

the screw is unscrewed.

The CO2 value increases when the

screw is tightened.

After making any adjustments with

the offset regulating screw, the

CO2 value at maximum output

must be rechecked by carrying out

the above described steps.

Replacing the gas valve and CO2 and offset regulator

We reserve the right to make changes to dimensions and design in the interest of technological advances.

If the unit is not set to

“normal mode“, the control

board will automatically re-

set the unit after 20 minutes.

NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO GPM 55 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO GPM 55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info