587981
9
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
"Cooling Mode" button
Long pressing (>5 seconds)
switches between the cooling
and standby modes.
"Heating Mode" button
(only units with heat pump
function)
Long pressing (>5 seconds)
switches between the heating
and standby modes.
Symbol for compressors 1-6
Indicates the operation (lights
up) of the compressors. If the
LED is flashing, the correspond-
ing compressor is in safety time.
The "Pump" symbol lights up
when the circulation pump is
actuated.
The "Fan" symbol
lights up when the condenser
fan is actuated.
Thawing status LED
(only units with heat pump
function)
The LED indicates the opera-
tion (lights up) of the thawing
cycle during the heating mode
on the air-cooled condenser. If
the LED flashes, the controller
determines the required thaw-
ing time.
Symbol for anti-frost protection
medium heater
This symbol provides informa-
tion on the operating status
of the "anti-frost protection
medium heater" accessory.
"Menu" LED
Lights up when the parameter
level is activated.
Operation of the
iPro controller
The controller has 3 Modi:
1. Summer fan control (cooling
mode)
In cooling mode, the warmer me-
dium temperature is cooled to the
colder set value.
2. Transition mode (heating mode)
(only units with heat pump func-
tion):
In heating mode, the colder me-
dium temperature is heated to the
warmer set value.
3. Readiness mode (standby)
In standby mode, the safety equip-
ment is active and an operating
mode is not set.
"Menu" button
With this button, you can ac-
cess the function menu or set
the time and date.
"SET" button
With this button, you can select
a set value or parameter.
"" button
Pressing briefly can switch
between medium inlet, medium
outlet, condensation pressure,
and evaporation pressure. A
value can also be lowered.
"" button
Pressing briefly can switch
between medium inlet, medium
outlet, condensation pressure,
and evaporation pressure. A
value can also be raised.
"" and "SET" buttons together
Simultaneously pressing the
"" and "SET" buttons (>5
seconds) permits a change to
parameter levels 1 through 3.
"" and "SET" buttons together
Simultaneously pressing the
"" and "SET" buttons (<2
seconds) lets you leave param-
eter levels 1 through 3.
"" and "SET" together for
longer than 5 seconds
Simultaneously and longer
pressing the "" and "SET"
buttons (>5 seconds) enables
manual thawing (only units
with heat pump function).
"Vset" LED
Lights up when the dynamic set
value is activated.
Cooling mode LED
This LED indicates the selected
cooling mode.
Heating mode LED
(only units with heat pump
function)
This LED indicates the selected
heating mode.
"Cir1" symbol
Describes the specified value for
cooling circuit 1.
"Cir2" symbol
Describes the specified value for
cooling circuit 2.
"Flow!" symbol
Describes a medium volume
flow rate that is too low or too
high or no medium pressure.
General alarm LED
Indicates the respective fault in
combination with the code.
Value display (red display)
The value display shows current
values.
Parameter display (yellow dis-
play)
The parameter display shows
current values or parameters.
"°C" and "F°" symbol
Indicates which temperature
unit is shown in the value
display.
"Time" symbol
Indicates a value in a unit of
time.
"Bar" and "PSI°" symbol
Indicates which pressure unit is
shown in the value display.
+
+
Control panel of the IPS400D / IPC108E controller
+
bar
°C
F
PSI
Flow!
Vset
menu
Cir1 Cir2
menu
SET
IPS400DIPro
SMALL
bar
°C
F
PSI
Flow!
Vset
menu
Cir1 Cir2
menu
SET
IPS400D
IPro
SMALL
9
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO KWG500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO KWG500

REMKO KWG500 Bedienungsanleitung - Deutsch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info