587981
10
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Button functions
/ BUTTON
Activate and/or deactivate the unit by enabling the voltage supply to the
unit. The controller performs a self test and then indicates operational
readiness by the flashing of the LED 1 below the display.
Voltage
activated
Automatic
Approx. 1 min.
No voltage present Controller perform-
ing self test
Controller can be
operated
External enable
If a floating contact is used for the external enabling of the unit, the con-
troller shows "OFF" on the display and the display of the decimal places
flashes. The floating contact (Terminal 2-3) has priority for operation over
the controller.
Factory setting: Contact (Terminal 2-3) open = controller on
Possible connection: Contact (Terminal 2-3) closed = controller off
External enable
contact opened
Normal display
Units activated
Display
Unit deactivated
External enable
contact closed
The unit has three modes: Standby mode, summer fan control (cooling
mode), and transition mode (heating mode - only for units with heat
pump function). "StbY" is displayed in standby mode. All fault messages
and anti-frost protection resistors are active. The set cooling and heating
mode is indicated by the LED.
Please note: Changing the parameters can result in the programming of a
changed functional sense of the display!
Mode setting
> 5 sec. > 5 sec.
> 5 sec. > 5 sec.
HEATING MODE
Only KWG
COOLING
MODE
KWL and KWP
Cooling mode
Heating mode
Standby mode
SET value entry, cooling mode
Programming the set values
Using the "SET" button, the set value can be displayed during standby
or cooling mode. To change the set value, the "SET" button is pressed
for about 2 seconds. The display starts to flash. Using the "" or ""
button, the value can be set within the limits defined at the factory (St 02
+ St 03).
St 02 = 9.0°C Minimum set value, cooling mode
St 03 = 20.0°C Maximum set value, cooling mode
Factory setting = 11.0 °C
< 2 sec.< 2 sec. < 2 sec.< 2 sec. ...
Normal
display
Value
opened
Submenu
opened
Close
submenu
Entry of
new set value
< 2 sec.
REMKO KWG
10
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO KWG500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO KWG500

REMKO KWG500 Bedienungsanleitung - Deutsch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info