Bedienungsanleitung REMKO KWG600 (Seite 19 von 60) (Englisch)

587982

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Malfunction

Fault Code Possible cause Check Remedy

The unit

does not

start or

switches

itself off

autono-

mously

Power failure

Is all other electrical equipment

functioning?

Check the voltage and wait for

reactivation.

Unit fuse / main disconnecter

switched off

Does the unit have power?

Switch on the unit fuse / main

switch.

Waiting period too short Is the compr. symbol ﬂashing?

Plan for a longer waiting

period.

C(n)Mn

The maintenance interval

of compressor (n) has been

reached

Have the compressor mainte-

nance performed by a specialist

company

Reset the operating hours after

the maintenance interval.

AEP(n)

The maintenance interval of

the circulation pump has been

reached

Have the circulation pump

maintenance performed by a

specialist company

Reset the operating hours after

the maintenance interval.

APS /

ASPh

Incorrect electrical direction of

rotation of the mains supply

Has the phase sequence relay

switched through?

Change the direction of rota-

tion.

StbY

The controller is in standby

mode

Does the compressor symbol

light up?

Apply voltage and

select the operating mode.

Return temperature or param-

eter setting incorrect

Check the setting. Change the settings.

OFF No fault

Is the "external enable" ena-

bling contact closed?

Close / open

contact used.

AP1 Defective sensor, medium inlet Check of resistor PB1 Replace the defective sensor.

AP2

Defective sensor, medium

outlet

Check of resistor PB2 Replace the defective sensor.

AP 3-6 Defective transm. condensation Check of transmitter PB Replace the defective transmit..

Defective sensor, outdoor tem-

perature

Check of resistor PB Replace the defective sensor.

Atr1

Cabled remote control not con-

nected

Check of the connection / line

of the cabled remote control

If missing, set Parameter CF 74

from "1" to "0"

b(n)HP

High-pressure fault

Circuit n

Are the fans rotating?

Is the air inlet of the condenser

free of objects?

Have it checked by

a specialist company.

b(n)LP

Low-pressure fault

Circuit n

Is the pressure in the cooling

circuit OK?

Have it checked by

a specialist company.

b(n)hP Overtemperature of condenser

Are the fans rotating?

Is the air inlet of the condenser

free of objects?

Have it checked by

a specialist company.

b(n)hP

Undertemperature of condenser

Circuit n

Have the operating tempera-

tures been exceeded?

Decommission the system.

b(n)AC

b(n)AH

Anti-frost protection has

reacted

Circuit n

Is the temperature of the inlet

ﬂow 4°C or lower?

Increase the return temperature,

increase the medium volume

ﬂow rate

AEFL

Differential pressure monitor /

ﬂow monitor

reacted

Are the following items OK:

- Medium volume ﬂow rate

- No air in the medium

lines

- Circulation pump capacity

- Switches the differential pres-

sure /

ﬂow monitor

- Shut-off valves open

- Medium pressure too low

Have it checked by

a specialist company.

Atr1

Cabled remote control not

conﬁgured or connected

Does the cabled remote control

function perfectly?

Have the remote control and/

or parameters checked by a

specialist company.

AEt1,

b(n)tF,

A(n)tr,

b(n)HP

APS /

ASPh

Control fuse F1 230V triggered Has fuse F1 triggered?

Have the fuse replaced by a

specialist company.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO KWG600 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO KWG600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info