Bedienungsanleitung REMKO KWG600 (Seite 21 von 60) (Englisch)

587982

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Mounting instructions for expert personnel

■

For the installation of the entire

system, the operating instruc-

tions of the indoor units and

the chiller and/or heating sys-

tem must be observed.

■

The indoor units and chiller

work independently. They do

not have to be interconnected.

■

Select an installation site that

guarantees free air inlet and

outlet. See the "Minimum

clearance" section.

■

Do not install the unit in the

direct vicinity of units with

intensive heat radiation.

Installation in the vicinity of

heat radiation reduces the unit

output.

■

Lift the unit only at the in-

tended points. Never load the

medium or refrigerant lines.

■

The medium connection lines,

valves, and connections must

be insulated in a vapour-

diffusion-tight manner. If

necessary, the condensate

line (only units with heat

pump function) must also be

insulated. In combined systems

with cooling and heating

modes, the requirements of

the current energy savings

ordinance (Energie-Einspar-

Verordnung (EnEV) in

Germany) must be observed.

■

Protect open lines against the

penetration of dirt. Never press

in the lines.

■

Avoid unnecessary bends.

■

Establish all electrical

connections according to the

locally valid regulations.

■

Always connect electrical

lines properly to the electrical

terminals.

Fires may otherwise result.

■

Observe the static and other

construction regulations and

conditions in regard to the

installation site.

■

When selecting the installation

site, pay attention to a possible

noise reﬂection of the units in

the environment and on the

mounting surface.

■

To prevent the transmission of

vibrations to the mounting sur-

face, the units must be mount-

ed on vibration-absorbent

materials or vibration-isolated

foundations.

Make sure the lines are also

vibration-isolated.

■

If special requirements are

placed on the noise emissions

of the installation site, locally

adapted sound insulation

measures must be taken.

In such cases, please contact

a corresponding specialist

consultant.

Important information

prior to installation

2 Vertical unit transport

Tension point

1 Upright unit transport

Transport

■

Bring the unit as close

as possible to the installation

site

while still in the original

packaging. In this way, you can

prevent

transport damage.

■

The units may be moved only

into their mounting position

(upright) using suitable means

of transport (Figure 1).

Secure against tipping!

■

The unit must be transported

in a vertical position to higher

installation sites (Figure 2).

■

Check the package contents

for completeness and check the

unit for visible transport dam-

age.

Report any damage immediate-

ly to your contracting partners

and the shipping company.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO KWG600 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO KWG600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info