587902
8
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
8
REMKO PGT (E) series
Gas connection
The use of longer hose lines
is permissible if:
- special operational reasons exist
- appropriate additional safety
measures are observed and
the hose lengths are kept
as short as possible
Hose lines must be
fundamentally protected
against chemical, thermal and
mechanical damage
In particular, torsional stress
must be avoided
The units may only be operated
out of the gas phase
The units must be serviced
by qualified persons only
Only original spare parts may
be used for repairs
Unit parts that are prone to
wear and ageing (e.g. gas
hoses) must be replaced at
regular intervals
Gas connection nipple on
the unit - G1/4 LH - KN
When selecting the hose, make
sure that the pressure class is
sufficient
The gas connection / unit
operation must take place
exclusively on the basis of
the accident prevention regulation
DGUV 79 “
Use of liquid gas”
,
as well as the respective local
construction and fire prevention
regulations.
The fuel supply must be installed
in accordance with DIN 4755 for
oil-fired warm air heaters, DVGW
Code of Practice G 600 for gas-
fired warm air heaters and TRF for
liquid gas.
The units are operated with liquid
gas in accordance with DIN 51622.
They require a constant
unit
connection pressure of 1.5 bar.
It is prohibited to exceed or
undershoot the connection
pressure.
When using longer hose lines,
consider the respective pressure
loss
Only use components that have
been tested and are suitable for
the respective purpose, such
as gas hose, pressure controller
and hose breakage protection
or leak gas protection
If possible, the length of the gas
hose should not exceed 2 m
Only pressure controllers with
a fixed outlet pressure setting
are permitted. The units may
only be operated out of the gas
phase
CAUTION
The units must not be used
below ground level
, e.g.
in basements, without suitable
gas monitoring equipment.
CAUTION
A constant unit connection
pressure of 1.5 bar (1500
mbar) must be guaranteed,
also in continuous operation.
NOTE
This does not apply
if the correct condition
is confirmed by an expert.
CAUTION
Before all work on the gas
supply and when replacing
gas cylinders, all shut-off
valves must be closed and no
ignition sources are permitted
in the immediate vicinity.
NOTE
It is prohibited to exceed
or undershoot the required
connection pressure.
All common gas cylinder sizes
are permitted for the gas
supply. However, a gas
cylinder with at least 11 kg
filling weight is recommended.
For longer operation and
nominal heat outputs above
50 kW, it is recommended that
the gas be drawn from several
gas cylinders in parallel. (Multi-
cylinder accessories set)
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO PGT 60E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO PGT 60E

REMKO PGT 60E Bedienungsanleitung - Deutsch - 28 seiten

REMKO PGT 60E Bedienungsanleitung - Holländisch - 24 seiten

REMKO PGT 60E Bedienungsanleitung - Französisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info