Bedienungsanleitung REMKO RKL350 (Seite 8 von 16) (Englisch)

587567

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Prior to Initial Operation

The unit is set up in the desired location with the air out-

let side facing the room. Follow the safety instructions

when setting up the unit.

Keep doors and windows closed

during operation.

In case of direct sunlight, make sure

to close all curtains and blinds.

Recommendations for optimum unit operation.

5 MIN.

There must be a minimum of 20 cm between the

back of the unit and the wall.

Expelling the warm air

During cooling mode, the unit generates warm air. This

air must be expelled from the room to retain the cooling

effect.

It is therefore necessary to insert the supplied exhaust

hose into the air outlet opening at the back of the unit.

The exhaust hose must always be placed at an in-

cline in the direction the air is flowing!

In some circumstances, low pressure can occur in the

setup room when air is being expelled via a perma-

nently attached exhaust hose, e.g. as a result of closed

windows or doors. If the performance of the unit is ad-

versely affected as a result, make sure that the pressure is

corrected.

Make sure that the deflector piece

from the top slides down into the

notches on the side until it clicks into

place.

To ensure that the unit operates ef-

fectively, do not place the flexible ex-

haust hose supplied at sharp angles

and make sure there are no kinks.

Different ways of expelling air

You can expel air from the building as follows:

1. With a flat nozzle.

The flat nozzle supplied can be

used in different ways.

It is possible to guide the flat nozzle

through the open window and se-

cure it firmly using straps and suc-

tion devices.

The flat nozzle can also be hung

through the partially opened win-

dow.

2. With a fixed connection to the ex-

haust hose (wall lead-through).

The hose supplied is firmly con-

nected to a wall lead-through.

Lead-through kits can be pur-

chased as accessories.

Circulation filter

Condensation

drain with plug

You may not extend the exhaust hose.

The air expelled from the unit contains a certain

amount of moisture. We therefore recommend ex-

pelling the air to the surroundings or the outside.

After unpacking the unit, place it on

its transport wheels and let it stand

for a minimum of 5 min. before

switching it on.

Place the unit securely on a level

and firm surface.

An uneven surface can cause vibra-

tions and disruptive noises.

Before plugging in the power cord,

make sure that the required current is

available!

230V / 1~, N, PE / 50 Hz.

If extension cords are necessary,

make absolutely sure that they are

sufficiently thick.

All extensions of the power cords

must be sufficiently thick and may

only be used if they are completely

extended.

Make sure that there is a plug for the

condensation drain and that it has

been securely placed.

Water may leak out after the unit be-

comes operational.

Never operate the unit without the

intake filter.

Without an air intake filter, the plate

fins of the evaporators become dirty

and the unit’s performance is ad-

versely affected.

Make sure that people and objects,

such as plants in the room, are not

directly in the path of the expelled air.

Exhaust filter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL350 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL350

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info