Bedienungsanleitung REMKO RKL350 (Seite 9 von 16) (Englisch)

587567

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Timer Operation

The timer can be preset to switch the unit on or off for a

maximum of 12 hours. Pressing the “SET” button in-

creases the time until the unit is switched on or off by

one hour.

The number of hours is shown on the display.

Timer switches unit off automatically:

1. W hen the unit is on, press the

“SET” button; the “OFF” LED lights up.

2. Set the desired amount of time until the unit is

switched off with “SET” button.

Keep in mind that after the setting has been made,

the display changes to show the target temperature.

3. After the set amount of time has elapsed, the unit

switches off automatically.

Timer switches unit on automatically:

The unit switches on with the most recently made set-

tings. If you want different settings, you must switch the

unit on, make the changes and then switch the unit off

again.

1. When the unit is switched off, press the “SET” but-

ton ; the “ON” LED lights up.

2. Set the desired amount of time until the unit is

switched on with the “SET” button.

Keep in mind that after the setting is made, the dis-

play changes to show the target temperature.

3. After the set amount of time has elapsed, the unit

switches on automatically.

Initial Operation

Prior to initial operation, the air intake and outlet open-

ings must be inspected for foreign bodies and the air in-

take filter for dirt. Blocked or dirty grilles and filters must

be cleaned immediately. See the chapter “Maintenance

and Service“.

Cooling mode

1. Switch the unit on with the “I/O” button.

2. Select cooling mode with the “Mode” button.

The “AUTO” LED must be lit up.

3. Set the target temperature you want with the

“THERMO CONTROL” buttons.

The selected target temperature appears on the

display.

4. If the set fan speed is too high or too low, the de-

sired fan speed can be set by pressing the “MODE”

button.

Fan mode (circulation)

1. Switch the unit on with the “I/O” button

2. Select fan mode with the “MODE” button. The “FAN”

LED must be lit up.

Information about timer mode (timer clock)

The timer function is reset by pressing the “I/O” but-

ton.

If the “SET” button is pressed while the timer is acti-

vated, the remaining time is shown on the display

and can be changed using the same “SET” button.

If the timer is programmed, this setting may be lost if

the unit is disconnected from the power supply.

Shutting Down the Unit

To shut down the unit, always switch it off with the

“Power” button on the control panel or via the remote

control. Only now can you unplug it from the power sup-

ply. Never shut the running unit off by pulling the power

plug.

Storage

If the unit is to be taken out of operation for a longer pe-

riod of time, for example, over the winter, proceed as

follows:

1. Let the device run for approximately 2 hours in circu-

lation mode (FAN) to dry the surface of the evapora-

tor plate fins.

This removes the remaining moisture from the unit

and prevents unpleasant odours when the device is

put back into operation.

2. Switch off the unit by pressing the “I/O” button, un-

plug the unit from the power supply and roll up the

power cord.

3. Make sure that the cable is not bent and there are

no kinks.

The cable can be attached to the back of the unit.

4. Place a suitable container under the condensation

drain of the internal tank.

The condensation drain is located at the bottom at

the back of the unit.

5. Pull the plug from the condensation drain and collect

the water that drains out.

6. Then replace the plug.

Keep in mind that if there is no plug or it is inserted

incorrectly, water may leak out after the unit has re-

sumed operation.

7. Store the unit in an upright position in a dry location

that is protected from direct sunlight and dust.

8. To prevent dust from getting inside the unit, protect it

with, for example, a plastic cover.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL350 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL350

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info