Bedienungsanleitung REMKO RKS371H (Seite 21 von 28) (Englisch)

587735

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Wiring Diagram

Connecting the outdoor part

The connections of the outdoor part are located inside

the unit above the connection valves. Proceed as fol-

lows to connect the lines:

1. Remove the cover of the terminal strip on the right-

hand side of outdoor part.

2. Guide the lines through the strain relief.

3. Connect the customer-supplied connection lines of

the units to the outdoor part and the indoor unit as

shown in the figure below.

4. Also connect the sensor line of the RKS 350 H unit

to the corresponding connections on the outdoor part

and indoor unit.

5. Secure the control lines in the strain relief and re-

place the cover of the terminal strip.

Condensation

Condensation flow to the outdoor part

Condensation forms during heating operation on the

plate fin exchanger of the outdoor part because tem-

peratures below the dew point are reached.

The lower housing panel of the outdoor part is designed

to function as a drain tray. A condensation connection

has been supplied beneath the condenser or in the cen-

tre of the tray to be used by means of the seal.

If the unit is used for heating in areas susceptible to

frost, the lower housing panel must be kept free of frost

to ensure that the condensation can always drain out.

Condensation drainage on the indoor unit

Condensation forms during cooling operation on the

plate fin exchanger of the outdoor part because tem-

peratures below the dew point are reached.

The drainage trays of the indoor units are equipped with

a condensation hose. This hose must be placed at an

incline to ensure that the condensation drains.

Condensation hose on the outdoor part

Condensation can be guided over longer distances us-

ing a customer-supplied condensation hose.

Ensure the following before laying the condensation

hose:

àMake sure that there is an adequate incline for drain-

age.

Minimum of 2 %.

àWhen the unit is in operation at an outside tempera-

ture of below 0 °C, the hose must be protected

against frost.

If necessary, use a hose heating mechanism.

àAlways use suitable hose clips.

àAfter the hoses have been put into place, you must

check that the condensation flows freely.

1. Place the seal on the hose

connection piece.

2. Press the connection piece

into the opening for this pur-

pose.

Seal

Connection

piece

Resulting

connection

Assembling the condensation connection

RKS 327 H and RKS 335 H

Outdoor part

Compressor control

Neutral conductor

To the reverse valve

Protective conductor

N(2)

To the condenser fan

Power suppl

Indoor unit

N(2)

230 V~,

50 Hz,

L1/N/PE

RKS 350 H

Outdoor part

Compressor control

Neutral conductor

To the reverse valve

Protective conductor

N(2)

To the condenser fan

Power suppl

Indoor unit

N(2)

230 V~,

50 Hz,

L1/N/PE

Sensor line to the AT

Plug

RKS 371 H

Power suppl

Indoor unit

230 V~,

50 Hz,

L1/N/PE

Outdoor conductor

Neutral conductor

To the reverse valve

To the condenser fan

Protective conductor

To the compressor

Sensor line

Not in use

N(2)

Outdoor part

contactor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKS371H Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKS371H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info