Bedienungsanleitung REMKO RKS371H (Seite 23 von 28) (Englisch)

587735

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Connections of the condensation pump on the wa-

ter side

The reservoir is attached to the condensation collection

tray connection of the indoor unit via a customer-

supplied hose (20 mm Ø). The factory-installed flexible

hose of the condensation tray must be disassembled.

The supplied ventilation hose must be used for the res-

ervoir to function properly.

The end of the ventilation hose must at least be at the

same height as the condensation tray to prevent water

from overflowing. The supplied metal wire clips are

used to secure the hose in a vertical position

Keep the hose from being suspended which will prevent

an air pocket from forming.

Prior to Initial Operation

After the pressure check has been performed, the vac-

uum pump must be connected to the valve connections

of the outdoor part (see section “Impermeability Check”)

by means of the manometer station and a vacuum cre-

ated.

Prior to initial operation of the unit and after contact with

the cold cycle, the following checks must be performed

and documented in the initial operation log:

àCheck the refrigerant lines, the outdoor part and the

indoor unit to ensure that any remaining moisture

has been completely removed.

àCheck all refrigerant lines and shut-off valves for

leaks with a leak locator spray or soapy water when

the unit is not in operation.

àCheck that the electrical connection between the in-

door unit and the outer part has been correctly at-

tached.

àCheck the electrical control line to ensure that it is

securely attached in the terminals.

Loose lines in the terminals can cause fires.

àCheck the refrigerant lines and insulation for dam-

age.

àCheck all fixtures and suspended parts to ensure

that they are in the proper position and at the correct

height.

If the refrigerant line is longer than 5 m, more re-

frigerant should be added to the system.

Electrical connection of the condensation pump

There is an electrical connection area located under the

hose connections. This area also a cover that can be

taken on and off.

The pump is equipped with an alarm contact that

switches off the indoor unit and can also control a cus-

tomer-installed malfunction/alarm system.

The electrical connections may only be made by author-

ised service personnel in accordance with the relevant

regulations.

Local guidelines for operation as well as the require-

ments established by local energy supply companies

must be observed for setup and initial operation.

Initial operation of the condensation pump

Before putting the pump into operation, the lines that

have been laid must be checked to ensure that they are

functioning properly and leakproof.

1. Switch the power supply of the pump on.

2. Pour distilled water into the condensation tray until

the pump switches on from the reservoir.

Pump operation can be heard when it is being oper-

ated for the first time or being put back into opera-

tion. After it has run for short period, the noise nor-

malises.

3. Keep in mind that the pump automatically switches

off once the water has been pumped out of the res-

ervoir.

4. If upon initial operation there is a lot of noise from vi-

brating hoses, insulate these hoses using foam

hoses.

Condensation buildup is prevented when using insu-

lated hoses sealed against diffusion.

5. Check the function of the alarm contact by drastically

increasing the amount of water.

The alarm contact should switch off the unit.

Always use a contactor or relay to switch off the

outdoor part!

The 6 mm (inner diameter) thick hose is placed at a

maximum height difference of 6 meters to the drain.

If the pump is installed outside the unit, a maximum

height difference of 3 meters between the lower edge of

the unit and the pump mounted above may not be ex-

ceeded. The condensation line should be as vertical as

possible to guide the condensation.

The reservoir and pump are connected to one another

with the long suction hose and the plugable sensor line

from the reservoir. To ensure that the pump operates as

quietly as possible, the suction hose should not be

shortened.

Kondensatab-

laufschlauch

Entlü

tungsschlauch

(kurz)

Pumpe

Reservoir

Ansaugschlauch

(

lang

)

Tropfwann e

Condensation

drainage hose

Ventilation hose

short

Pump

Condensation tray

Reservoir

Suction hose

(long)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKS371H Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKS371H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info