Bedienungsanleitung Renkforce WS-WN575A3 (Seite 5 von 12) (Deutsch, Englisch, Holländisch, Französisch)

796999

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

“Repeater” quick set-up via WPS

Please note that the mode selection slider (6) must be in the „Repeater“ position, if

youintendtocongureoverWPS.

The repeater clones the WLAN name and password of your wireless LAN router dur-

ingthecongurationprocess.Whendone,asufxisplacedattheendoftheWLAN

name so that you you are able to distinguish between your router’s wireless network

and that of the repeater’s.

• StarttheautomaticcongurationviaWPSbypressingtheWPSbutton(2) on the repeater

for about 6 seconds.

Releasethebutton.TherstWLANLEDturnsoffandtheWPSLEDbeginstoashfast.

• Press the WPS button on your WLAN router within 2 minutes. Alternatively, you could also

use the WPS function on the router’s web interface.

Please refer to the operating instructions of your router.

• TheWPSLEDwillstopashingwhenthecongurationiscomplete;thesignalstrengthof

your wireless network connection is shown by means of the 3 WiFi LEDs.

• SelecttheWLANwiththesufxtoconnectadevicetoyourwirelesslocalareanetwork.The

WLAN password is the same as your router’s WLAN password.

Now you could also connect devices to the other two network ports.

Operating modes overview and web interface access

a) “Repeater” mode

• OnceyouhavesetuptheproductviaWPS,youshouldmakesomebasiccongurations

on the web interface (like setting the region and changing the login password) (see chapter

Basiccongurationonthewebinterface(allmodes)).Theproductisreadyforuseafterthat.

• IncaseyouhavenotsetuptheWPSconguration,gotothechapter“ManualRepeater

conguration”afteryouaredonewiththebasicconguration.

• In either case, you should connect a computer or mobile device to the wireless LAN or to

oneoftherepeater‘stwonetworkports.Oncetherepeateriscongured,useyoursame

router password for the WLAN; otherwise your wireless local area network is not encrypted.

• Openyourbrowserandthenthecongurationpageoftherepeaterhttp://ap.setup.

TheinternalDHCPserverwillrun,iftherepeaterisnotyetcongured.Insuchacaseyou

canalsoopenthecongurationpageusingthedefaultIPaddress192.168.10.1.

Butifyourrepeaterisalreadyconguredandyouareexperiencingissueswhileopening

thecongurationpage,please,restartyourcomputerandyourrepeater(byswitchingoff

and on again). Alternatively, you could use the IP address to open the web interface. Since

the repeater is already integrated in your network, you can look up the IP address of your

WLAN router. Please refer to the manual of your router.

b) “Access point” mode

• As soon as the access point is correctly connected to your router, it is usually ready for use.

Alsointhiscasehowever,youshouldmakethebasiccongurationonthewebinterface

andcongureWLAN(chapter“Accesspoint”conguration).

• Connect a computer or a mobile device to the WLAN or the LAN port of the AP.

• OpenyourbrowserandthenthecongurationpageoftheAPhttp://ap.setup.

If the web page does not load, use the IP address to open the page. Since the AP is already

integrated in your network, you can look up the IP address of your WLAN router. Please

refer to the manual of your router.

c) “Router” mode

• Connect a computer or a mobile device to the WLAN or to the LAN port of the router.

• Opentheroutercongurationpage.EntertheURLhttp://ap.setup or the default IP ad-

dress 192.168.10.1 to do this.

• Sinceyoucongurethe“Router”modeviathewebinterface,makethebasiccongurations

rstandthenconguretherouter(chapter“Router“conguration”).

d) Log in to the web interface (all modes)

• Selectyourdesiredlanguagerstandwaitforthepagetoreload.

• Enter the default password adminforthewebinterfaceintotheeldwiththelockandlogin.

Basic conguration on the web interface (all modes)

• In the web interface select your region and your time zone.

• Then enter a new web interface password.

• Conrmwiththebluebutton.

 IfyouhavesetuptherepeaterviaWPS,yourbasiccongurationisnowcomplete.

But you can of course change other settings later.

 Whenyoureopenthewebinterfaceafteryouhavesetupthebasicconguration,

use the login password you have just created; don’t enter the default login pass-

word.

“Access point” conguration

• Ifsetupdoesnotstartautomaticallyafteryouhavecompletedthebasicconguration,click

the second button to the left in the blue bar at the bottom.

• You could also change the two names of the WLAN networks (2.4 and 5 GHz).

• Now choose the WLAN encryption. We recommend selecting WPA2-PSK, which offers

the highest security. However, if you have devices, which only support WPA, select both

standards.

• Enter your WLAN password. Your password should consist of at least 8 characters and

include numbers as well as upper and lower case letters.

• Thenclickonthebluebuttontoconrm.Oncethechangeshavebeenapplied,theset-up

is complete.

 IfyouhaveconguredthesettingsviaWLAN,youshouldnowconnectyourdevice

to the new WLAN network.

If you would like to make other changes to the settings, click on the Setup button

in the lower right corner of the web interface or on the Wi-Fi button for the WLAN

settings. The current status of the device is shown under Status.

“Router“ conguration

• Ifthesetupdoesnotstartautomaticallyafteryouhavecompletedthebasicconguration,

click the second button to the left in the blue bar at the bottom.

• Select the Internet access type. If you have for example a DSL connection with your access

data, select PPPoE here.

• EnteryourusernameandpasswordforyourDSLconnectionintheappropriateelds.

• You could then also change the two names of the WLAN networks (2.4 and 5 GHz).

• Now choose the WLAN encryption. We recommend selecting WPA2-PSK, which offers

the highest security. However, if you have devices, which only support WPA, select both

standards.

• Enter your WLAN password. Your password should consist of at least 8 characters and

include numbers as well as upper and lower case letters.

• Thenclickonthebluebuttontoconrm.Oncethechangeshavebeenapplied,theset-up

is complete.

 IfyouhaveconguredthesettingsviaWLAN,youshouldnowconnectyourdevice

to the new WLAN network.

If you would like to make other changes to the settings, click on the Setup button

in the lower right corner of the web interface or on the Wi-Fi button for the WLAN

settings. The current status of the device is shown under Status.

Renkforce WS-WN575A3 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info