Bedienungsanleitung Renkforce WS-WN575A3 (Seite 6 von 12) (Deutsch, Englisch, Holländisch, Französisch)

796999

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

Allrightsincluding translation reserved. Reproduction byanymethod,e.g.photocopy, microlming, or the capturein

electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

Manual “repeater” conguration

• Ifthesetupdoesnotstartautomaticallyafteryouhavecompletedthebasicconguration,

click the second button to the left in the blue bar at the bottom.

• Selectthedesiredlanguagerstandwaitforthepagetoreload.

We recommend selecting “Bridge“, the second mode option listed in the dropdown menu.

Oncecongured,therepeater’sDHCPserverwillbedisabledinthismode,andyourdevice

connects to your router as the default gateway. Thus you will be able to access your network

normally, even if your device is currently connected to the repeater.

TherstmodeoptionleavestheDHCPserverenabled.Basically,thiswouldcreateanew

separate network.

• After that click in the list below on the WLAN that your repeater should use to connect to

or you wish to extend.

You can refresh the list by clicking the two round arrows.

• TheWLANnameisautomaticallycarriedovertoyourrouter.Asufxwillalsobeplacedat

the end of the name. You could however change the two names, is you like.

• Now you still need to enter the password of the WLAN network that you have selected

earlierintotheblankeld.

• Last but not least, click the blue button to connect. Once the changes have been applied,

the set-up is complete.

 IfyouhaveconguredthesettingsviaWLAN,youshouldnowconnectyourdevice

to the new WLAN network.

If you would like to make other changes to the settings, click on the Setup button in

the lower right corner of the web interface. The current status of the device is shown

under Status.

Positioning of the “Repeater”

• Nowthatyouhaveconguredtherepeater,youwillneedtoplaceitinanappropriateposi-

tion as shown in the following illustration.

• Try several locations and then select the best place with the best connection to your existing

WLAN router.

• At least 2 LEDs of the WLAN should be lit to indicate that your repeater is not placed too

far away from your router.

Resetting to factory settings

Proceed as follows to reset the product to factory settings.

• Plug the device into a mains socket.

• Use the slider (3) to switch on your device and wait until the start-up process has completed.

• Hold down the sunk button (1) for more than 3 seconds. Then release the button again.

• The product will restart with the factory settings. This process will last approx. 2 minutes.

Care and cleaning

Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions

since these could damage the housing or even impair operation.

• Always unplug the product from the power socket and disconnect all the connecting cables

before cleaning it.

• Use a dry, lint-free cloth to clean the product.

Disposal

Electrical and electronic equipment does not belong in the regular household waste.

Once the product becomes unusable, dispose of it in accordance with the relevant

statutory regulations.

Declaration of conformity (DOC)

We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this

product conforms to the 2014/53/EU directive.

The full text of the EU conformity declaration is available via the following Internet

address:www.conrad.com/downloads

 Selectalanguagebyclickingaagsymbolandentertheordernumberoftheprod-

uctinthesearcheld;thenyouwillbeabletodownload the EU declaration of

conformity in PDF format.

Technical data

Operating voltage ................................. 100 - 240 V/AC, 50/60 Hz, max. 0.3 A

Ports ..................................................... 1x RJ45 LAN 100 Mbit; 1x RF45 WAN/LAN 100 MBit

WLAN ................................................... EEE802.11b/g/n, 2.4 GHz, max. 300 MBit;

IEEE802.11a/n/ac, 5 GHz, max. 867 MBit;

Transmit frequency range ..................... 2.412 – 2.472 GHz, 18.02 dBm;

5.180 – 5.240 GHz, 18.42 dBm

Encryption protocols ............................. WPA2; WPA

Operation modes .................................. Repeater; Access Point; Router

Dimensions (W x H x D) .......................approx. 50 x 73 x 52 mm (without antennas)

Dimension antennas (Ø x L) .................approx. 10 x 91 mm

Weight ..................................................approx. 111 g

Operation conditions ............................. 0 °C to +40 °C, max. 10 - 90% rF

(relative air humidity, noncondensing)

Storage conditions ................................-10 °C bis +70 °C, 10 - 90% rF (noncondensing)

Renkforce WS-WN575A3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info