Bedienungsanleitung Renusol ConSole (Seite 5 von 8) (Englisch)

613882

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Renusol ConSole · EN · 04/2011 — 5

ASSEMBLY PREPARATION

Calculating the amount of ballast for the

ConSole

The wind loads acting on the ConSole re-

quire it to be weighed down with ballast.

Gravel, stones, plates and similar materials

are suitable as ballast.

The table opposite can serve as a guide for

the required ballast. These values are calcu-

lated according to DIN 1055-4:2005-03 and

Eurocode. Several years experience confirm

the reliability of the system.

The exterior module series and column re-

quire more ballast according to the table.

The values indicated prevent the ConSoles

from tipping over, sliding or being lifted-

ConSoles.

In order to ensure safety against sliding, the

coefficient of friction between the roofing

and the ConSole must be greater than 0.6 .

This can be established using a spring

scale. A ConSole filled with 100 kg of ballast

should only move from the spring scale

under a horizontal tensile force of over

60 kg.

Additional ballast

In a higher wind load zone: 30% more bal-

last per level.

When using extension rails: 10% more bal-

last.

In case of excess length of the modules on

the side:

additional ballast in proportion to the excess

length.

Calculation basis

The ballast values are calculated for wind

load zone 1 for Germany according to DIN

1055-4:2005-03 and for terrain category III:

Suburbs, industrial or commercial zones and

forests.

*The system weight is not included in the

recommended ballast values.

Recommended ballast values for ConSoles in kg in terrace systems*

A = minimum distance of the ConSolen series:

ConSole 4.1 >1.2 m

ConSole 4.2/5.2/6.2 >1.5 m

B = minimum

roof edge > 1/5 h

h = Building height

Schematic diagram of a ConSole terrace system

Distances between rows on the ConSole system

Positioning the ConSoles

Check whether the installation surface

(e.g., the roof) is enough for the additional

roof load.

The surface must be level, clean and not

too slippery. With slippery surfaces, e.g.,

with PVC roof membranes, an anti-slip mat

should be used, e.g., a building protection

mat.

Place the ConSole with the opening facing

south. A minimum distance of a fifth of the

building height "h" should be maintained

from the side of the roof. Building height 10

metres => minimum distance 2 metres.

The minimum distance between

the ConsSoles is clear from the schematic

diagram.

Filling ballast

Now fill in the correct ballast. Reference

values here are contained in the table

"Recommended ballast values" at the top

of this page.

Ballast diagrams for all ConSole types are

available on our website

www.renusol.com/download as a PDF le.

inner ConSoles

in the slipstream

circular,

non-binding

roof area

outer,

wind-exposed

ConSoles

Roof edge

Building height

Up to 8 meters Up to 12 meters Up to 16 meters

interior exterior interior exterior interior exterior

ConSole 4.1 62 99 73 115 82 128

ConSole 4.2 58 94 68 110 77 122

ConSole 5.2 63 106 75 123 84 137

ConSole 6.2 83 134 98 156 110 173

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Renusol ConSole Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info