Bedienungsanleitung Riho Whirlpool Electronic LCD (Seite 13 von 28) (Englisch)

626525

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Z1209004. 5 GB

Enjoy the RIHO life-style

Whirlpool Electronic LCD user handbook

4.1.4 Diverse options

- Light function option.

Switch on only if there is sufficient water (bath full indication ).

The light will switch on after pressing the light pushbutton once. The light function will switch off after 20 minutes.

If the light function is on and the water level drops (2 seconds), the light function will switch off.

If the light function is switched on and the whirlpool motor is started, the time for the light function will be set at

the running time of the motor + 5 minutes. In other words, after the running of the whirlpool motor is

completed, the light will remain on for another 5 minutes. If the motor is switched off between times, the light

function will switch off 5 minutes later.

The light will switch off after pressing the light button briefly.

- Colour therapy option

Switch on only if there is sufficient water (bath full indication ).

When the light button is held down colour therapy switches on. Colour therapy will switch off after 20 minutes.

If you press the light button during colour therapy the colour changing stops. If you press the button again

colour changing restarts. If you wish to stop the function earlier then hold down the light button and the colour

therapy will be turned off.

If the colour therapy is on and the water level drops (2 seconds), the colour therapy will switch off.

If the colour therapy is switched on and the whirlpool motor is started, the time for the colour therapy will be set

at the running time + 5 minutes. In other words, after the running of the whirlpool motor is completed, the light

will remain on for another 5 minutes. If the motor is switched off between times, the colour therapy will switch

off 5 minutes later.

Technical info: The light exists of LED lights. LED lights have a very long lifecycle and therefore don't have to

be replaced. In case the color therapy is malfunctioning, it can only be replaced or repaired by a certified

installer.

Technical info: The color therapy exists of LED lights. LED lights have a very long lifecycle and therefore don't

have to be replaced. In case the color therapy is malfunctioning, it can only be replaced or repaired by a

certified installer.

light indication colour therapy indication

If the whirlpool system is fitted with heating a heating unit is installed in the suction pipe of the Ist hydromoter.

This unit can only provide heat if water is actually flowing through it. The 1st hydro system must therefore be

switched on. When you have switched on the heating unit, this is displayed on the screen (for hydro function)

by the symbol . This symbol also indicates the required temperature that is set. As soon as the required

water temperature (see water temperature indication) is reached the heating switches off automatically.

If the temperature drops, the heater will automatically go back on. To measure the temperature of the water a

temperature sensor is located near the heating unit.

The heater option is designed to heat the water to maintain temperature and not to bring cold water, for

example 19 °C to 45 °C.

45°C

Water temperature indication

4.1 Basic functions

This pushbutton is used to switch the hydro system on and off.

- Short press, switch system on/off.

- Long press, see user options

In the case of the hydro-whirlpool system with back and foot jets that are separately connected by a

valve, or are controlled by a pump, the button can be used to move through the various

combinations one after the other.

This pushbutton is used to switch the ground system on and off.

- Short press, switch system on/off.

- Long press, see user options.

This pushbutton is used to adjust the speed of the motor for a pulsation effect. The display shows when the

pulsation starts. The display has two of these buttons. The pulsation button operates the system to the left of

this button.

The following description applies to both buttons, which can be operated independently.

- First push, the system automatically pulses water between 35% and 100% for a period of about 8 seconds.

The display shows pulsating waves.

- Second push, the system operates automatically at the speed at the moment when the button is pushed.

- Third push, the system automatically returns to 100% operation and begins to pulse automatically again.

See first push.

- Switch off the pulsation position by pressing and holding down the pulsation button.

If you start with this button instead of or , the system will then start pulsating directly.

If you require both pulsations to be on, this is then possible. The pulsation effects of each system run

synchronously with each other for maximum effect.

Pulsation position

4.1.1 Hydro-system.

4.1.2 Ground system.

4.1.3 Pulsation positions.

4.1.5 Heating option

-41--40-

heating indication

19°C 12:1019°C 12:10

19°C 12:10

12:10

19°C 12:10

45°C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Riho Whirlpool Electronic LCD Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Riho Whirlpool Electronic LCD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info