Bedienungsanleitung Riho Whirlpool Electronic LCD (Seite 15 von 28) (Englisch)

626525

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Z1209004. 5 GB

Enjoy the RIHO life-style

Whirlpool Electronic LCD user handbook

4.1.7 Run dry function

Automatic run-dry function:

If you take a bath and the level sensor is covered with water for 5 minutes (bath full indication ), the

automatic run-dry function (8minutes) will start after the bath is emptied. During the 8 minute waiting period the

LCD screen will display the countdown time. The run-dry function will then start.

Attention: This function may be switched off by a dipswitch at the time of installation.

4.2 Menu functions

Beneath this button there are extra functions for switching on and off. This depends to a great extent on the

system that you have bought and the options associated with it. This section describes all the possibilities, but

if you don't have the options that are discussed then the option functions will not appear on the screen.

ATTENTION: The button has several functions. If you press and hold down this button you access

a programmer menu that will be discussed later.

4.2.1 Short menu (select menu options).

If you press this button briefly the following screen appears:

Short

Manual

run-dry

function

Automatic

run-dry

function

If both buttons are pressed down simultaneously for 2 seconds the run dry function starts if there is “no” water

in the bath (bath empty indication ).

The following occurs automatically:

- The display shows the run-dry function.

- The shut off valve opens after 5 seconds

- The hydro motors will be switched on for a few seconds.

- The aero-motor will be switched on for 45 seconds.

- The motors then stop and the display shows RIHO again.

If both buttons are pressed simultaneously for two seconds the cleanpool function starts, provided that the

level indication shows full and there is sufficient liquid in the reservoir and no other function is active (no light).

All jets must be completely under water.

1: Display shows clean function and countdown timer.

2: After 8 seconds all motors and valves are switched on.

The motor of the aero-system on the other hand switches alternately on and off (20 seconds.

This is to achieve a cleaning process in the aerojet housing.

3: After 7 seconds the cleanpool switches on for 3 seconds.

4: The motors stop after 1½ minutes with circulation pumping prior to a pause of 30 seconds

5: The motors are restarted for 1½ minutes. The motor of the aero system should then start

switching off and on alternatively again

6: End of cleaning function, system returns to rest.

7: The display shows that your bath needs to be evacuated and that the water contains cleaning

material and is therefore not suitable for bathing.

Note:

If the water level drops the cleaning cycle stops.

If you wish to end the cleanpool function earlier press once on one of the two buttons or .

Display clean function

with countdown timer

Display bath evacuation.

You will not be able to

use any function until the

system is evacuated.

Warning

No cleaning fluid

present

4.1.6 Cleanpool option.

-43--42-

12:10

178 sec

12:10

20 sec

19°C 12:10

okok

12:10

480 sec

12:10

20 sec

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Riho Whirlpool Electronic LCD Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Riho Whirlpool Electronic LCD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info