Bedienungsanleitung Roadstar HRA-1300DAB (Seite 5 von 19) (Deutsch, Englisch, Französisch, Italienisch)

592133

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

English English

5 6

longer the bar will be from left to right.

DLS

DLS stands for Dynamic Label Segment which is a scrolling message that the broadcaster

may include in their transmissions. The message usually includes information such as

programme details …etc.

Programme type

This describes the style of the programme that is being broadcast. If the information is

not available, the display will show

“<Program Type>”.

Ensemble/Multiplex (Group name)

The Ensemble/Multiplex is a collection of radio stations that are bundled and transmitted together

in a single frequency. There are national and local multiplexes, local ones contain stations that

are specific to that area.

Note: Press and hold the INFO button for longer than 2 seconds, the software version number

will be displayed.

FM RADIO

1. To select FM, repeatedly press the MODE button until you see “Switch to FM” is displayed,

the display will finally show FM

and the frequency.

2. To activate auto search, turn and hold the SELECT control until it starts to scan the

frequency band, the display will show

“Searching … > .” or “Searching … < .”, and it will stop automatically once a station has been

found.

3. To activate manual tuning, repeatedly turn the SELECT control and when you see your

desired frequency appears in the display, release the control.

4. To select the FM stereo/mono reception mode, press the SELECT button to toggle

between the “Auto” or “Mono” selection.

Note: The radio will automatically switch between the stereo and mono reception, but you can

override this and switch this function manually which is helpful for poor signal reception.

STORING AND RECALLING STORED STATIONS

In either DAB or FM mode, you can store up to 10 stations to the favourite presets; this will

enable you to get direct access to your favourite stations.

1. To store a preset, first tune to your desired station, then press and hold the PRESET

button until the display shows “Save to P#” and flash.

2. Repeatedly turn the SELECT control to select your desired station preset number then

press the SELECT button to confirm your selection, the display will show “Preset # saved”.

3. To recall a preset station, first press the PRESET button once, then repeatedly turn the

SELECT control to scroll up or down

the presets that you have stored. When the display shows your desired preset number, release

the control. If the preset hasn’t been allocated a station, the display will show “Empty preset #”.

ALARM FUNCTION (AC operation only)

This unit incorporates an identical Dual Alarm function in AC operation. You can have

two individual alarm wake-up time and wake-up mode settings to wake you to an

electronic buzzer tone or your favourite radio station (DAB/FM). There is no alarm

function in battery operation.

Setting the alarm time and wake-up mode

1. Press the ALARM button once to enter into the Alarm Menu, then repeatedly turn the

SELECT control followed by pressing on the SELECT button to select Alarm (1 or 2).

2. Again repeatedly turn the SELECT control to select “Alarm Setting”, then press the

SELECT button to confirm, the display will show “Alarm # Setting” and the hour digit of the

alarm time will flash.

3. Repeatedly turn the SELECT control followed by pressing on the SELECT button to

adjust and confirm your desired alarm time first set the hour and then the minute.

4. After the confirmation of the minute setting, the alarm time is set and you will enter into

the wake-up mode settings.

5. Again repeatedly turn the SELECT control followed by pressing on the SELECT button

to adjust and confirm the wake-up mode settings first set the DAB and FM Preset (1-10),

then the Buzzer Tone (1 or 2), finally the alarm Volume level.

6. After the confirmation of the alarm volume level setting, the wake-up mode settings are

all completed and the alarm function

is now ready for you to activate.

7. Repeat the above procedures to set the other Alarm (1 or 2).

Activating the alarm function

1. To activate the alarm function, first press the ALARM button to enter into the Alarm

Menu, then turn the SELECT control followed by pressing on the SELECT button to select

Alarm (1 or 2).

2. When the display shows “Alarm Source”, press the SELECT button to go for the

selection.

3. Repeatedly turn the SELECT control and the associated alarm wake-up mode will be

displayed and changed in the below sequence:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roadstar HRA-1300DAB Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info