Bedienungsanleitung Robbe Futaba FF-10 (Seite 68 von 119) (Englisch)

520097

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

LINEAR PROGRAMMABLE MIXES (

PROG.MIX1-4

Sample reasons to use linear programmable mixes:

• To correct bad tendencies of the aircraft (such as rolling in response to rudder input).

• To operate 2 or more servos for a single axis (such as two rudder servos).

• To automatically correct for a particular action (such as lowering elevator when ﬂ aps are lowered).

• To operate a second channel in response to movement in a ﬁ rst channel (such as increasing the amount of smoke oil in

response to more throttle application, but only when the smoke switch is active).

• To turn off response of a primary control in certain circumstances (such as simulating one engine ﬂ aming-out on a twin,

or throttle-assisted rudder turns, also with a twin).

Adjustability:

• Defaults: The 4 programmable mixes default to the most frequently used mixes for simplicity. If you want to use one of

these mixes, simply select that mix number so that the master and slave servos are already selected for you.

•

PROG.MIX1

aileron-to-rudder for coordinated turns

•

PROG.MIX2

elevator-to-ﬂ ap for tighter loops (

HELI

mixes default to elev-to-pitch.)

•

PROG.MIX3

ﬂ ap-to-elevator to compensate pitching with ﬂ aps (

HELI

mixes default to pitch-to-elev.)

•

PROG.MIX4

throttle-to-rudder ground handling compensation

•Channels available to mix: All four mixes may use any combination of CH1-8. (CH9-10 are not proportional and cannot

be mixed.) Offset and dials may also be set to the master channels. (see below.)

•Master: the controlling channel. The channel whose movement is followed by the slave channel.

•Another channel: Most mixes follow a control channel. (Ex: rudder-to-ailerons, 25%, no switch, corrects roll

coupling.)

MASTER SLAVE LINK TRIM SWITCH POSITION RATE OFFSET

RUDD AILE ON OFF

ANY

NULL 25% 0

•Offset as master: To create an

OFFSET

mix, set the master as OFST. (Ex: move ﬂ aperons as ﬂ aps 20% of their total

throw when SWITCH C is in down position.)

MASTER SLAVE LINK TRIM SWITCH POSITION RATE OFFSET

OFST FLAP ON

N/A

C DOWN 20% 0

• Dial as master: To directly effect one servo’s position by moving a dial, set the master as the desired dial.

(Ex: create a second throttle trim on left slider.)

MASTER SLAVE LINK TRIM SWITCH POSITION RATE OFFSET

VR(D) THRO OFF

N/A ANY

NULL 5% 0

•Slave: the controlled channel. The channel that is moved automatically in response to the movement of the master

channel. The second channel in a mix’s name (i.e. aileron-to-rudder).

•Link: link this programmable mix with other mixes.

Ex: PMIX

FLAP-ELEVATOR

mixing to correct for ballooning when ﬂ aps are lowered, but model has a V-tail. Without

LINK

Your 10C contains four separate linear programmable mixes. (Note that mixer

#5-8’s mixing

RATEs

are set with a 5-point curve.

HELI

has mixer #5-6's mixing.

see CURVE MIXES, p. 71.)

There are a variety of reasons you might want to use these mixes. A few are

listed here. All of the adjustable parameters are listed below, but don’t let them

scare you. For your ﬁ rst few times experimenting with mixes, just turn on the

default mixes, adjust them how you think they need to be, then use the servo

screen to check and see if you were correct. As with all functions, a sample

setup follows, step by step, to assist you.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FF-10 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FF-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info