Bedienungsanleitung Robbe Futaba FF-10 (Seite 78 von 119) (Englisch)

520097

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

A LOOK AT THE RADIO'S

GLID

-SPECIFIC FUNCTIONS STEP BY STEP.

Those functions which are identical to the

ACRO

setups are referred directly to those pages.

MODEL

TYPE

: This function of the

PARAMETER

submenu is used to select the type of model programming to be used.

GLIDER TYPES:

Before doing anything else to set up a glider or sailplane, ﬁ rst you must decide which

MODEL

TYPE

best ﬁ ts your aircraft.

•

ACRO

: for some aerobatic/slope gliders,

ACRO

is a better choice because of functions it offers that the

GLID

types do not.

•

ACRO

provides:

•

SNAP-ROLL

•

AILEVATOR

(twin elevator servo support),

•

AIRBRAKE

(a more assignable version of

BUTTERFLY

• For nitro-powered sailplanes:

IDLE-DOWN

THR-CUT

THROTTLE-NEEDLE

mixing and

THROTTLE DELAY

programming.

• But

ACRO

lacks programming for full-span ailerons and separate OFFSET trims for each ﬂ ight condition: Normal,

Start, Speed, Distance and Landing.

•

GLID(1A+1F)

: The

GLID(1A+1F)

MODEL

TYPE

is intended for sailplanes with one or two aileron servos (or none), and a single

ﬂ ap servo (or two connected with a y-connector). This

TYPE

is meant to be a very simplistic version to set up a basic

glider without a lot of added features. Additional ﬂ ight conditions available.

•

GLID(2A+1F)

: The

GLID(2A+1F)

MODEL

TYPE

is intended for sailplanes with dual aileron servos and a single ﬂ ap servo (or

two connected with a y-connector) Additional ﬂ ight conditions available. These ﬂ ight conditions contain different offset

trims and aileron differentials to make the sailplane perform certain maneuvers more easily.

•

GLID(2A+2F)

: The

GLID(2A+2F)

MODEL

TYPE

supports dual flap servos that can also act as ailerons, creating full-span

ailerons and ﬂ aps. Additional ﬂ ight conditions available. These ﬂ ight conditions contain different offset trims and aileron

differentials to make the sailplane perform certain maneuvers more easily.

GOAL of EXAMPLE: STEPS: INPUTS:

Change model1 is

MODEL

TYPE

GLID(1A+1F)

NOTE:

This is one of the several

functions that the radio requires

conﬁ rmation to make a change.

Confirm you are currently using the

proper model memory. (Ex: 1)

On home screen, check model nameand

number on top left.

If it is not the correct model (Ex: 1), use

MODEL SELECT

, p. 25.

Open

PARAMETER

submenu.

for 1 second.

(If

ADVANCE

, again.)

to 2nd page of menu.

PARAMETER

Change the

MODEL

TYPE

Conﬁ rm the change.

TYPE

. to

GLID(1A+1F)

for one second.

Are you sure?

Conﬁ rmation displays.

to conﬁ rm.

Close.

GLID(1A+1F)

(FLAPERON)

AIL1

FLP2

(CH1)

AIL2

FLP1

(CH6)

AIL1

(CH1)

AIL2

(CH7)

FLP

(CH6)

GLID(2A+1F)

AIL1

(CH1)

FLP1

(CH6)

FLP2

(CH5)

AIL2

(CH7)

GLID(2A+2F)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FF-10 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FF-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info