Bedienungsanleitung Robbe Futaba FX-40 (Seite 6 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Transmitter controls

FX-40

5.1 GENERAL INFORMATION

The FX-40 transmitter is supplied with all transmitter controls

installed as standard:

•

Four stick controls

• Three linear proportional controls (L1 … L3)

• Three central rotary knobs (LD, CD, RD)

• Six rotary trimmers (T1 … T4, T7 + T8)

• Two digital trim buttons (T5 + T6)

• Four left-side switches (SA, SB, SE, SF) and four rightside

switches (SC, SD, SG, SH) plus one momentary push-

button in the rotary knob (CD-SW).

• Two optional stick-switches or buttons can be installed in

the primary sticks.

• This makes a total of 29 transmitter controls which can be

assigned to any function in any sequence.

Data can be entered either using the touch-screen function of

the LCD screen, or with the 3-D Hotkey and the buttons S1 …

S4. The latter can also be used as Direct buttons; in this case

they are assigned to any function so that you can call up fre-

quently used mixer functions quickly.

• AERIAL COMPARTMENT

The transmitter aerial is located in its own compartment on the

left-hand side of the transmitter case (as seen from the fr

ont).

Befor

e operating the transmitter, withdraw the aerial from the

compartment, insert it in the aerial base and twist it to engage

the bayonet lock.Replace the aerial in its compartment for

transport and storage.

• AERIAL BASE

Installing the aerial: insert the aerial into the bayonet fitting,

ess it down and r

otate it to the right through about 15°; the

aerial will now snap into place. Important: the aerial must

engage fully!

Removing the aerial: press the aerial down and disengage the

lock by rotating it to the left. The aerial can now be r

emoved.

The tilt angle of the aerial base is adjustable. T

o alter the angle

of inclination, loosen the locking screw in the aerial base, swi-

Locking

screw

LED monitor

vel the ball mounting to the angle required, then tighten the

locking screw again. The set is supplied with a 2.5 mm A/F

allen key which fits the locking screw.

• LED MONITOR

The aerial base also houses the LED monitor which indicates

the transmitter’

s status with flashing sequences and dif

ferent

colours.

• When you switch the transmitter on, the LED monitor

initially cycles through all seven flashing colours to check

its function.

• When the internal processing sequence commences, the

LED monitor flashes yellow at a high rate.

• When the process is completed, the LED monitor flashes

pink at a high rate.

Up to this point the transmitter radiates no power.

Eventually the screen displays the query “transmit?”; if you

ess the button to answer yes, the LED monitor switches to

een.

The green LED is the standard indicator

, confirming that the

transmitter is active and broadcasting an RF signal.

• If the LED monitor flashes yellow at a low rate, this alerts

you to a war

ning message on the Start scr

een display.

• If the LED monitor flashes blue at a low rate, this indica-

tes that the spot frequency is being transmitted to the

receiver; when this process is completed, the LED reverts

to pink.

• The LED monitor changes to blue when the DSC cable is

connected, or the transmitter is active as a Pupil unit in

Trainer mode.

• If the LED monitor flashes red at a low rate, this indicates

that no RF module is present, or that the RF module in the

transmitter does not match the transmitter or the selec-

ted frequency band.

SUMMARY OF THE MOST IMPORTANT COLOUR INDICA-

TORS:

Green = RF transmission

Red or pink = no RF transmission

• RE-POSITIONING THE SWITCHES

The transmitter is supplied as standard with various types of

switch installed. You may wish to inter

change them to suit your

personal pr

eferences, and this can be carried out easily both

electrically and mechanically.

• Unscrew the transmitter back panel

• Unplug the connector from the switch you wish to re-

position

• Locate the combination tool supplied in the set, and

remove the rubber cap. Under the cap you will find a spe-

cial spanner which fits the crown nuts used to secure the

switches.

• Undo the appropriate crown nut by rotating the spanner

to the left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info