Bedienungsanleitung Robbe Futaba FX-40 (Seite 7 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Transmitter controls

FX-40

In the Linkage menu “Dial Monitor” the current and stored

positions of the rotary knobs are displayed in bar graph form.

The centre rotary knob CD is a digital control with no end-

stops, and it also features an integral push-button function

(CD-SW). This control can also be assigned freely to any func-

tion. The transmitter emits an audible signal when the knob is

moved to the centre position. The position of this control is

also displayed on the Start screen.

• LINEAR SLIDERS

The centre of the transmitter houses three linear sliders with a

centr

e detent. These analogue contr

ols can also be assigned

freely to any function you wish. The transmitter emits an audi-

ble signal when the slider is moved to the centre position.

In the Linkage menu “Dial Monitor” the current and stored

positions of the linear sliders are displayed in bar graph form.

• DIGITAL TRIMMERS

The transmitter features two digital trimmer buttons (T5 + T6).

Every time a button is moved, the trimmer value alters by the

selected incr

ement. If a trimmer button is held at one end-

point in or

der to adjust the trimmer value by a larger amount,

the rate of change automatically accelerates (auto-repeat

function).

If the trimmer position reaches the neutral point (centre posi-

tion), or passes the neutral point, the transmitter emits an

audible signal. The current trim position is displayed as a bar

graph in the Start display and also in the “Dial Monitor” menu.

The trimmer buttons can be assigned freely to any functions,

and can also be used as transmitter controls for mixer func-

tions.

The trimmer rate and increment can be selected individually

for each trim button in the “Function” menu.

• You can fit the switches in any position you like.

The default position of the switches is as follows:

In each case the centre wir

e of the cable is colour-coded, and

is assigned permanently to the following switches:

Please ensure that the wire

colours are correctly connec-

ted after you have r

e-positio-

ned the switches, otherwise

the graphical on-scr

een

assignment will be displayed

incorrectly.

• After re-positioning the switches, fit the crown nuts again

and tighten them using the special spanner supplied.

• Fit the back panel and tighten the retaining screws.

After the re-positioning exercise you should now call up the

System menu “Switch” (page 35) and alter the switch types

and position numbers, so that the graphical switch position di

play reflects the new configuration and is displayed correctly on

the screen.

• CENTRAL ROTARY KNOBS

The rotary knobs LD and RD are analogue contr

ols which can

be assigned freely to any function. They feature a fine centre

detent, and the transmitter emits an audible signal when they

are moved to the centre position. If you wish, they can be

retracted by pushing the knob in using light pressure.

Switch Position Typ Lever

SA 3-position Change-over Short

SB 3-position Change-over Short

SC 3-position Change-over Long

SD 3-position Change-over Short

SE 3-position Change-over Short

SF 2-position Change-over Long

SG 3-position Change-over Short

SH 3-position Change-over Short

SWITCH Cable colour

SA and SC green

SB and SD yellow

SE and SG orange

SF and SH brown

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info