Bedienungsanleitung Robbe Futaba FX-40 (Seite 20 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Switching the transmitter on

Changing the frequency

channel

FX-40

7. SWITCHING THE TRANSMITTER ON / OFF

• Locate the switch on the transmitter marked “Power”, and slide it

to the right.

•

After the loading and initialisation phase (monitor LED flashes yel-

low) the scr

een displays the spot frequency confirm field, and the

monitor LED flashes pink.

• The request to check the spot frequency appears every time you

switch the transmitter on.

• If the transmitter is set to the correct channel, and you wish to trans-

mit an RF signal, press the “Yes” button.

• The colour of the monitor LED now changes to a continuous green,

indicating that an RF signal is being broadcast.

• If you press “No”, the display switches to the Start menu, and no

RF signal is transmitted.

In this case you can now carry out adjustments without radiating

an RF signal, or change the spot frequency, so that the transmitter

starts on the correct channel next time you switch it on.

NOTE:

If the transmitter was last switched on more than four hours previous-

ly, the initialisation phase will take a little longer (cold start). If a D/P card

is fitted this will also pr

olong the start phase slightly

, as the transmitter

must first read all the files on the card.

CAUTION:

Never switch the transmitter off during the initialisation phase

(monitor LED flashes yellow), as this could corrupt the set-

tings.

SWITCHING THE TRANSMITTER OFF

• Move the “Power” switch on the transmitter to the left.

•

This action cuts of

f RF transmission, and causes the data in

the working memory to be written to the transmitter’s inter-

nal memory or the D/P card. During this process the moni-

tor LED flashes yellow, and the screen displays the mes-

sage “Storing model data”.

Switching the transmitter on again during the power-off / data

storing process could also cause damage to data, so the

transmitter ignores your action if you do this.

LANGUAGE SWITCH ENGLISH GERMAN

If your transmitter is set to German screen displays and you

wish to switch to English, please follow this procedure:

•

Switch the transmitter on; the query “T

ransmit?” appears

on the screen

• Press the “No” button

• Call up the System menu by pressing the “S1” button, then

press the “Information” button.

• At bottom left press the “German” button in the Language

field, then select “English”, and switch the transmitter off.

• Switch the transmitter on again, and the screen displays will

now be in English.

8. CHANGING THE SPOT FREQUENCY

The system incorporates a DD Synthesizer system which

generates the spot frequencies. The channel is selected at the

transmitter by softwar

e, and information on the selected chan-

nel is sent to the receiver using the Wireless Frequency Setting

System (WFSS); the receiver responds by switching to the

same channel.

The new spot frequency is stored in the receiver - even when

it is switched off - until the channel is changed again.

• Press the Spot frequency field in the Start menu

• The screen displays the “Frequency” setup menu.

• Check that the set receiver number (label on the back of

the receiver) is entered correctly, because it is only possi-

ble to transmit a spot frequency if the appropriate receiver

number is transmitted at the same time.

• Press the Spot frequency button, and the screen displays

a three-page table of channels, showing all the frequencies

approved for use in Europe. Select a channel which is per-

mitted in the country in which you wish to operate the

model. A summary of the frequencies approved for use in

European countries is supplied with the system.

• Press the “Enter” button to confirm the new spot frequen-

cy you have chosen. (Press “Return” if you wish to inter-

rupt this function without making a change.)

Frequenzkanalwahl

Frequenzbandwahl

Modulationsartwahl

Empfängernummer

Nr. für 2. Empfänger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info