Bedienungsanleitung Robbe Futaba FX-40 (Seite 83 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Model menu

Snap roll

Multi-motor

FX-40

The servo transit speed of all three control surfaces can be

entered individually for each direction, separately for the

‘there’ and ‘back’ directions. A separate programming mask is

provided in the second display level, as shown below.

Mark the appropriate field, and enter the desired value using

the arrow buttons. The adjustment range is 0 to 27 increments.

The highest number equates to a servo travel time of up to

nine seconds.

The screen shot below shows a typical servo run time set-up:

When you have completed the programming of a snap roll

manoeuvre, it is fundamentally essential to check everything

very carefully on the model itself.

18.20 MULTI-MOTOR

SETTINGS FOR MULTI-MOTOR MODELS

This function enables you to define the most important set-

tings for contr

olling the motors in a model air

craft with up to

four power plants. These settings are as follows:

• Motor cut-off functions (Motor off)

• Idle settings (Idle 2)

• Idle-up (Auto-rotation)

• Full-throttle trims (Trim max.)

• Idle trims (Trim idle)

To enter values for these settings you must first activate each

of the throttle servos (THR, THR2), and then enter the servo

position as a percentage.

With the ‘Power model’ type already set, mark the ‘Multi-

motor’ option in the Model menu. The screen display now

looks like this:

This menu will differ according to the particular model type

you have selected. The number of throttle channels displayed

on the screen is dictated by the number defined in the model

configuration. Our example shows two (maximum: four).

The first step is to activate the whole function for each throttle

channel (THR, THR2 etc.) in the Status line: mark the field, and

the display changes from ‘INH’ (inactive) to ‘ON’.

After this you can enter the settings for ‘Motor off’ and ‘Idle 2’

for each motor: the first step is to activate the function in the

Status line, and then enter the servo position (Posi.). Mark the

appropriate field to activate the function, then enter the posi-

tion in the form of a percentage value. After marking the field

you can a new value using the arrow buttons. The adjustment

range is 0% to 50%; the default setting is 17%. Pressing

‘Reset’ restores the default setting.

In the bottom line you will see the Auto-rotation (Motor Hold)

option, which can be activated individually for each motor.

Mark the appropriate field: the screen displays ‘ON’, and the

throttle servos run to the values set in the ‘Motor pos’ window.

This option sets one motor to a particular value, so that you

can adjust a second motor independently of it.

In the second level of the display you can set the values for the

trims - for full-throttle and idle - separately for each motor. The

required value is entered as a percentage figure in the ‘Rate’

line, using the arrow buttons. A separate field contains the pre-

fix, so you can reverse the direction of the servos if necessary

to suit your installation. The adjustment range is 0% to 30% in

each case. The default setting is 0%; pressing ‘Reset’ restores

that setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info