467096
19
Zoom out
Zoom in
Vorherige Seite
1/128
Nächste Seite
19
<Before Use>
Connector/Plug
Ɣ'6&7UDLQHUƔ%DWWHU\FKDUJH
Connector for trainer function
When you use trainer function, connect the
optional trainer cable between the transmitters for
teacher and student.
*You can set the trainer function on the Trainer Function
screen in the system menu.
Connector for DSC function
You can operate the transmitter without
transmitting radio waves by connecting the
transmitter and the receiver to the DSC cable.
*Please refer to the section "Connection between Receiver/
Servo"
Connector for battery charger
This is the connector for charging the Ni-
MH battery HT6F1700B that is installed in the
transmitter. Do not use any other chargers except
the attached special charger corresponding to Ni-
MH battery.
Danger
Do not connect any other chargers except the
special charger to this charging connector.
*If you take out the Ni-MH battery HT6F1700B from
the transmitter, you can use the optional quick charger
CR-2000 corresponding to Ni-MH battery.
Installing and Removing of the battery
HT6F1700B for the transmitter
Attachment of the battery
1. Open the battery cover on the rear of the
transmitter toward upper side.
ƔBattery ribbon for
removing battery
2. Install the battery in the holder.
ƔBattery ribbon
*Push the battery
until being locked
completely.
ƔConnector
3. Connect the battery connector.
4. Close and lock the battery cover completely.
Removing of the battery
Note: If you remove the battery while the
power is on, the data you have set will not
be saved.
1. Open the battery cover on the rear of the
transmitter toward upper side.
2. Disconnect the battery connector.
3. Pull up the battery ribbon to release the lock.
4. Remove the battery.
5. Close and lock the battery cover completely.
Warning
Be careful to not drop the battery.
Never disconnect the battery connector
from the T12FG transmitter while
some message are displayed on the
screen after turning off the power the
T12FG transmitter.
* Internal devices such as memories may be damaged.
* If there is any problem, the message "Backup Error" will
be shown the next time when you turn on the power of the
transmitter. Do not use the transmitter as it is, send it to the
Futaba Service Center.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Robbe Futaba T-12 FG wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Robbe Futaba T-12 FG

Robbe Futaba T-12 FG Bedienungsanleitung - Deutsch - 78 seiten

Robbe Futaba T-12 FG Bedienungsanleitung - Holländisch - 80 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info