Bedienungsanleitung Robbe Futaba T6EX (Seite 6 von 38) (Englisch)

747912

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Trim levers (all) - Used to shift the neutral or center position of each servo as labeled in the diagram. Once either trim lever

is operated, the trim position is displayed on the LCD screen. Also once either edit key is operated, all trim positions are

displayed sequentially on the LCD screen.

NOTE: The throttle trim lever is intended for ﬁne tuning the throttle servo when the engine is at idle. Throttle trim does not

affect the throttle servo when the throttle control stick is all the way up (so idle r.p.m. can be adjusted without affecting

throttle settings through the rest of the stick movement).

Charging jack - Port for charging the transmitter batteries with the included battery charger.

On/off switch

DATA INPUT lever - Used to change the values of the various functions displayed on the LCD screen

Liquid – crystal display screen (LCD) - Displays programming modes and values entered.

MODE key - Used to scroll through and display the “11-14” different functions.

SELECT key - Used to display the values for the current function.

Throttle – cut button - To use the throttle-cut function, lower the throttle stick all the way, then push the throttle-cut button to

fully close the carburetor and shut off the engine.

Throttle/rudder control stick - Operates the servos connected to channel 3 (throttle) and channel 4 (rudder) in the receiver.

A:Trainer switch - Operates the trainer functions. To operate as a trainer switch the transmitter must be connected to another

transmitter via. a trainer cord (available separately).

H:Idle – up switch - This switch operates to change the ﬁght condition which sets the throttle curve and pitch curve of mid

air maneuvers (rolls, loops, stall turns) and 3D ﬂight.

A:Retractable landing gear switch/Channel 5 - Switch operates the servo connected to channel 5 in the receiver. If your

model has retractable landing gear, this is the control used to extend and retract the gear.

H:Gyro switch/Channel 5 - You can connect the sense adjust connector to channel 5 of the receiver to operate the gyro,

which has two different senses. Also if you use the Futaba GY401/502/611 Gyro, two different gyro sense settings on the gyro

function in this transmitter can be called by this switch.

Antenna - Radiates signals to the receiver. NEVER point at the model when ﬂying! See page 9 for detail.

Changing the Throttle Stick Ratchet System to Helicopter-touch

1. Open the battery cover on the back of the transmitter and remove the transmitter battery.

2. Remove the four transmitter rear case screws and remove the rear case.

3. Change the ratchet plate on the gimbal section to the smooth ratchet plate for helicopter use.

Ratchet plate

for airplane

Ratchet plate

for helicopter

(The above photos show a Mode 2 system as supplied. )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba T6EX Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info