Bedienungsanleitung Roblin Palma (Seite 11 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490276

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components and

ducting kits are optional accessories and have to be ordered, they are not automatically supplied

with the chimney hood.

IN THE EXTRACTION MODE:

a. Place the anti-backow ats item 8 over the round outlet item 6, the telescopic duct and connect the

ducting 150mm (6 INS) over the round outlet on top of the canopy and secure the connections with

appropriate clamping rings or adhesive tape (Fig. 6).

b. Remove the grease lters (see paragraph Maintenance) Fig. 5 being sure that the connector of the

mains cable is correctly inserted in the socket placed on the sides of the fan. Before tting the chimney

to the canopy make the electrical connection as described in the section titled ELECTRICAL. When

the electrical connection has been made, test the lights and the fan motor.

c. Each chimney stack consists of two sections. Encase the upper section in the telescopic bottom sec-

tion (Fig. 1 - item 7a & b) by making it exceed at least 150 mm, maintain it in this position with an

adhesive tape (in order to avoid scratches between the 2 sections). Place slightly the chimney on

the canopy and t the upper sections by expanding the chimneys to allow them to clamp around the

bracket item 2 and secure the chimney stacks to the brackets using the two M4 screws item 12c

provided. Attention scratches risk on the junction line of the canopy with the lower chimney.

Not remove the lm from the canopy before the complete tting of the chimney.

d. Fit the 3 deectors Item 9.

IN THE RECIRCULATION MODE:

a. Fit the recirculation spigot R onto the upper chimney wall bracket using the same xing screws (Fig.

2 item 2).

b. Connect the ducting 150mm (6 INS) not provided between motors item 6 and the recirculation spigot

and secure the connections with appropriate clamping rings or adhesive tape.

c. Remove the grease lters (see paragraph Maintenance) Fig. 5 being sure that the connector of the

feeding cable is correctly inserted in the socket placed on the side of the fan. Before tting the chimney

to the canopy make the electrical connection as described in the section titled ELECTRICAL. When

the electrical connection has been made, test the lights and the fan motor.

d. Insert the charcoal lter into the base of the motor housing and secure the lter with two metal secur-

ing straps item A as illustrated in Fig. 4.

e. Each chimney stack consists of two sections. Encase the upper section in the telescopic bottom

section (Fig. 1 - item 7a & b) by making it exceed at least 150 mm, maintain it in this position with

an adhesive tape (in order to avoid scratches between the 2 sections). Place slightly the chimney

on the canopy and t the upper sections by expanding the chimneys to allow them to clamp around

the bracket item 2 and secure the chimney stacks to the brackets using the two M4 screws item 12c

provided. Attention scratches risk on the junction line of the canopy with the lower chimney.

Not remove the lm from the canopy before the complete tting of the chimney.

f. Fit the 3 deectors Item 9.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Palma Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info