Bedienungsanleitung Robomow Tuscania 500 (Seite 88 von 268) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

512484

Zoom out

Zoom in

Vorherige Seite

1/268

Nächste Seite

WARNING!

Never let Robomow operate without supervision. Serious injury can

occur. Insure that the scheduled operating times that you program in

for automatic start and mowing are times when the mowing area will

be free of children and pets. Do not program times unless you are

certain

the area will be free of children, pets and bystanders.

Chapter 3 – Operation and Charging

3.1 Edge Mowing

The first mowing chore for Robomow is mowing the edge. Edge is the outer perimeter of the active

zone Robomow is working within. This is essential where you placed your perimeter wire in the wire

set-up.

Edge mowing provides a clean even cut around the perimeter and helps to minimize the amount of

trimming along walls and other obstacles.

Edge in Base Station Zone

–

- Robomow leaves the Base Station (at the scheduled time or when pressing the ‘GO’ button once) to

mow the edge of the lawn. It will mke exactly one turn until it reaches the Base Station contacts;

- It will reverse out and move back to continue mowing the inner area of your lawn (see paragraph

3.2).

Edge in None-Base Zone

–

- Place Robomow inside the lawn, switch on the Perimeter Switch on and press the ‘GO’ button once;

- Robomow will automatically find the edge (perimeter). It will now begin mowing the edge, completing

one to two complete passes around the perimeter and then turn into the lawn to mow the inner area

of the lawn;

- It will then drive into the lawn and begin what is called the scanning process (see paragraph 3.2).

3.2 Scanning (Mowing of the inner area)

The scanning process is simply a process whereby Robomow is moving across your lawn while it is

mowing.

Robomow’s movement pattern is irregular with combination of parallel lines in narrow passes. Keep in

mind that the Robomow will not mow all the grass on its first pass; in fact it will leave uncut grass in

between many of the passes it makes. This is expected and is entirely normal. These uncut areas will

be cut on subsequent passes of the Robomow across the lawn. Just like a dishwasher, wait until the

job is finished before you can appreciate the results.

Robomow will continue to run for the amount of time selected or for the default

‘MAX’ time, which is

generally 2.5 hours, depending on grass type and condition.

3.3 Skipping Edge Mowing

Robomow provides a means that will allow you to skip the edge mowing process and start directly with

the scanning (mowing) process. In order to do this, simply press the

‘GO’ button twice at the initial

startup of the mower. Pressing

‘GO’ the second time immediately following the first press will tell the

mower to skip mowing the edge.

3.4 Operation in Base Zone – Automatic Start

 Automatic Start mode is used as a fully automatic solution to maintain your lawn.

 This mode enables you to set a weekly program, and the mower will automatically start to mow and

drive back for charging at the Base Station when finished.

 To set the weekly program refers to Chapter 2.1.1, ‘Weekly program’.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow Tuscania 500 Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info