Bedienungsanleitung Robomow Tuscania 500 (Seite 89 von 268) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

512484

Zoom out

Zoom in

Vorherige Seite

1/268

Nächste Seite

3.5 Operation in Base Zone – Manual Start

Manual Depart mode can be used in cases such as the following:

- Mowing the lawn at times other than when programmed.

- When the lawn is occupied and the yard must be cleared of debris, objects, pets or people first.

 For initiating a manual start for mowing, press the ‘GO’ button once. Robomow will depart from the

Base Station and will mow the edge until it reaches the Base Station. It will reverse out and move

back to continue mowing of the inner area.

 To skip the edge mowing process, press the ‘GO’ button twice when initiating manual start and

mowing.

3.6 Returning to the Base Station

 Automatic Return

Robomow automatically returns to the Base Station at the end of every operation. It will recharge

and stay ready for the next scheduled start time that was scheduled.

 ‘Go to base’ option

You can manually send the mower to the Base Station from any point in the lawn by pressing the

upper scroll arrow once for the

‘Go to base’ message option - then press ‘GO’. The Robomow will

find the perimeter wire and will follow it until reaching the Base Station –

‘Searching base’

message is displayed during this sequence.

3.7 Operation in None-Base Zone

Non-Base Zone is defined as a separated area, where the user must drive the mower manually from

the Base Station or carry it by hand, to the area in order to mow it. It can be operated either by the

Perimeter Switch or the Base Station.

Important! When mowing in non-Base zone, it is required first to define the work time (refer to 2.1.2)

and to set the proper time depends on the zone area.

 Zone activation

Connected to the Base Station - the zone is activated automatically as the mower is taken out from

the Base Station. If an intermittent beeping is heard shortly after turning the switch on, there is a

problem of cut wire or poor wire splicing (refer to chapter 4 – Text messages and Troubleshooting

for further help). Listen to the beeps to identify the problem (refer to figure 1.24). You must correct

the problem before Robomow can operate automatically.

Connected to Perimeter Switch

- Robomow cannot operate unless the Perimeter Switch is turned

on. Press the

on/off button to turn on the switch. To verify switch operation, there is a green LED

located next to the button that will flash when operating properly. If an intermittent beeping is heard

shortly after turning the switch on, there is a problem of cut wire or poor wire splicing (refer to

chapter 4 – Text messages and Troubleshooting for further help). Look to see which of the red

LEDs is flashing to identify the problem (refer to figure 1.43). You must correct the problem before

Robomow can operate automatically.

 Place the mower inside the active perimeter.

 Press the ‘GO’ button. In a case where you have forgotten to turn on the Perimeter Switch, a ‘No

wire signal’ message will be displayed, reminding you to turn the switch on.

3.8 Completing the Operation

Base Station Zone –

When Robomow has operated the allotted time, it will switch off the mowing motor and will start

moving in lines towards one of the lawn edges, then it will follow the perimeter wire back to the Base

Station, to be charged and get ready for the next operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow Tuscania 500 Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info