Bedienungsanleitung Roland AT100 (Seite 125 von 148) (Englisch)

527335

125

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

123

Connecting with External Devices

Normally, you don’t need to install a driver in order to connect

the ATELIER to your computer. However, if some problem

occurs, or if the performance is poor, using the Roland

original driver may solve the problem.

Specify the USB driver you want to use, and then install the

driver.

Press the [Utility] button.

Press the Menu [ ] and [ ] buttons to

select “USB Driver.”

fig.10-12.eps

Press the Value [-] and [+] buttons to select

“GENERIC” or “ORIGINAL.”

Turn the ATELIER’s volume to the minimum

level, switch off the power, then turn it back on

again.

This setting remains stored in memory even while power is

turned off.

By connecting an external MIDI device and exchanging

performance data, you can control the performances on one

device from the other. For instance, you can output sound from

the other instrument or switch voice on the other instrument.

What’s MIDI?

MIDI, short for “Musical Instrument Digital Interface,” was

developed as a standard for the exchange of performance

data between electronic instruments and computers.

The ATELIER is equipped with MIDI connectors to let it

exchange performance data with external devices. These

connectors can be used to connect the ATELIER to an external

device for even greater versatility.

About MIDI Connectors

The ATELIER has two kinds of MIDI connectors.

Connecting these to the MIDI connectors on a MIDI instrument

makes it possible for the two instruments to control each other.

For instance, you can output sound from the other instrument

or switch tones on the other instrument.

You should also set the MIDI send channel as needed (p. 117).

fig.10-09.eps

MIDI Out Connector

Connect the external MIDI device to the MIDI IN connector

with an optional MIDI cable. The notes played on the

keyboard, movements of the Damper pedal, Expression data,

data indicating that a Registration button [1]–[8], etc., was

pressed will be transmitted to the external MIDI connector.

MIDI In Connector

Connect the external MIDI device to the MIDI out connector

with an optional MIDI cable. Performance messages from an

external MIDI device are received here.

These incoming messages may instruct the receiving MIDI

instrument to play sounds or switch voices.

The ATELIER contains two sound generators: one sound

generator for its own keyboards and one GM2/GS sound

generator (p. 133). Normally, musical data transmitted from

an external device to the MIDI In connector is sent to the

GM2/GS sound generator, but you can also set the “MIDI IN

Mode” parameter (p. 116) so that the keyboard sound

generator is controlled.

Making the Settings for the USB Driver

Setting

Descriptions

GENERIC

Choose this if you want to use the

standard USB driver that was included

with your computer.

Normally, you should use this mode.

ORIGINAL

Choose this if you want to use a USB

driver downloaded from the Roland

website.

Connecting MIDI Devices

AT-100-300_e.book 123 ページ２００８年５月７日　水曜日　午後３時３３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland AT100 Seite 125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland AT100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info