Bedienungsanleitung Roland CD-2 (Seite 83 von 96) (Englisch)

527439

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Reference

■ Problems with the Sound (continued)

Problem Cause and Action

See

Page

The input source (audio

source) is not output

● Could devices be connected to both the MIC 1 jack and GUITAR jack?

➔ If you connect devices to both the MIC 1 jack and the GUITAR jack, the sound

from the MIC 1 jack will not be input. If you want to input sound from the MIC 1

jack, remove the plug from the GUITAR jack.

● Could the setting of the [MIC SELECT] button be incorrect?

➔ Use the setting that’s appropriate for the input source.

● Could the line input be turned off?

➔ Turn the LINE IN “On.”

Insufficient volume from a

device connected to the

MIC 1/MIC 2/GUITAR/LINE

IN jacks

● Could you be using a connection cable that contains an internal resistor?

➔ Use a connection cable that does not contain an internal resistor (such as one from

the Roland PCS-series).

—

The sound recorded via

the internal mics is not

loud enough

● Did you adjust the input level of the internal mics?

➔ Use Int MIC Gain to raise the input level of the internal mics.

The recorded sound is

noisy or distorted

● Is the input level adjusted appropriately?

➔ Adjust the input level so that the level meter briefly reaches “-3 dB” when loud

sounds are input.

37,

● Could you have raised the input level for sources that are not connected?

➔ Even if no equipment is connected, we recommend that you set the input level to

the minimum (MIN) for all inputs that you are not recording.

—

● Could the [MIC SELECT] button be lit orange?

➔ Even if you are intending to record via external mics, a noisy recording may

indicate that you are actually recording from the internal mics. Set the [MIC

SELECT] button to the correct position for the audio source you intend to record.

● When recording the sound from an instrument connected to the LINE IN jacks,

could you be unintentionally recording the sound from another CD-2 source as

well?

➔ When recording only the sound from the LINE IN jacks, make sure that [MIC

SELECT] is off (unlit).

● Could you be applying a mastering effect while creating a music CD?

➔ Some mastering effect patches may cause noise or distortion when used with

certain types of material. Try changing to a different mastering effect patch.

● Is the output level set correctly?

➔ If you raise the output level too high, noise or distortion may occur in the sound

from the internal speakers. Use the [OUTPUT LEVEL] knob to adjust the volume.

An unwanted effect is

applied to the sound

● Could you have selected an effect?

➔ Turn the effect “Off.”

● Could a mastering effect be selected?

➔ Turn the mastering effect “Off.”

Sound is briefly heard

from the internal speakers

even though they are

muted

● Were you connecting or disconnecting headphones?

➔ If the speakers are muted (the [SPEAKER MUTE] button is lit), noise may be heard

from the internal speakers when you connect or disconnect the headphones; this

is not a malfunction.

—

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland CD-2 Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland CD-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info