Bedienungsanleitung Roland DJ-505 (Seite 21 von 32) (Englisch)

710374

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Operating the DJ-505

Synchronizing the TR-S Tempo with the Serato DJ Tempo

If you press the TR-S [SYNC] button, the tempo of the TR-S is synchronized

with the tempo of the song that’s loaded into the deck.

The tempo shown in Serato DJ’s virtual deck will be the same as the tempo

shown in the TR-S display.

Backing Up or Restoring TR-S Data

Backup

Here’s how to back up all patterns and instrument settings of the TR-S to

your computer.

1. While holding down the TR/SAMPLER [CUE] button, turn on the

power.

TR-S pads [1]–[16] and performance pads blink green.

2. Use a USB cable to connect the DJ-505 to your computer.

TR-S pads [1]–[16] and performance pads light green.

3. On your computer, open the “Roland” drive.

4. Open the “BACKUP” folder, and copy all les from dj_prm_kit1.

prm through dj_prm_kit12.prm and dj_prm_ptn1.prm through

dj_prm_ptn16.prm to your computer.

5. When copying is completed, operate your computer to eject

the “Roland” drive.

6. Disconnect the USB cable.

TR-S pads [1]–[16] and performance pads return to blinking green.

7. Turn o the power.

Restore

Here’s how to restore the backed-up TR-S data from your computer to the

DJ-505.

1. While holding down the TR/SAMPLER [CUE] button, turn on the

power.

TR-S pads [1]–[16] and performance pads blink green.

2. Use a USB cable to connect the DJ-505 to your computer.

TR-S pads [1]–[16] and performance pads light green.

3. On your computer, open the “Roland” drive.

4. Copy the backup les into the “Roland” drive’s “RESTORE”

folder.

5. When copying is completed, operate your computer to eject

the “Roland” drive.

6. Disconnect the USB cable.

7. Wait until the TR-S pads [1]–[16] and performance pads

blinking green.

NOTE

Never turn o the power until the TR-S pads and performance pads

blinking green.

8. Turn o the power.

Using the DJ-505 in Stand-Alone Mode

You can use the DJ-505 when it is not connected to Serato DJ (when Serato DJ

is not running).

In stand-alone mode, you can use the following functions in each section

of the DJ-505.

Section Available functions

Mixer section

[TRIM] knobs

* Does not work if the [CH 1] or [CH 2] switch is set to “PC.”

[HI], [MID], [LOW] knobs

[FILTER] knobs

Channel [CUE] buttons

Channel faders

[MASTER LEVEL] knob

[BOOTH LEVEL] knob

[MIXING] knob

[TR/SAMPLER LEVEL] knob

TR/SAMPLER [CUE] button

Cross fader

Front panel

[CROSS FADER CURVE] switch

[CROSS FADER REVERSE] switch

[CH 1], [CH 2] switches

[VOLUME] knob

[MIC LEVEL] knob

TR-S section

All functionality can be used except for Serato Sampler playback

and the [SYNC] button.

Deck section

A MIDI message is transmitted when you operate a button/knob.

Performance pads

* With the default settings, the unit is in TR mode. You can switch

to another mode, but in modes other than TR mode, pressing a

button or pad only transmits MIDI messages.

Others

5 When you move (press) a top panel controller (except for the

controllers of the TR-S section), MIDI messages are transmitted.

5 MIDI messages are transmitted from the PC port. Only MIDI

messages for synchronization are transmitted from the MIDI OUT

connector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland DJ-505 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland DJ-505

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info