Bedienungsanleitung Roland DJ-808 (Seite 23 von 32) (Englisch)

710397

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

System Settings

Pad/Button Item Value (Bold: default) Explanation

TR-S section

[BD] AUX mode

OFF

If this is “On,” the input signals to INPUT CH 1–4 and USB 3–4 are output without change to

MASTER OUT when the [INPUT SELECT] switch (front panel) is set to PC.

[SD] Backspin length

OFF

, (Short),

nrNL

(Normal),

Long

(Long)

When applying backspin to the jog dial, this setting lets you make backspin continue longer

than the distance that the jog dial actually rotated.

OFF Backspin operation occurs according to the actual distance of rotation.

Short Backspin operation is shorter than with the Normal setting.

Normal Backspin operation occurs longer than the actual distance of rotation.

Long Backspin operation is longer than with the Normal setting.

[ACC] Reverb type setting for the VT section

(Reverb),

(Delay),

(Reverb + Delay )

Species the eect that is operated by the [REVERB] knob of the VT section.

Reverb Reverb is applied.

Delay Delay is applied.

Reverb +

Delay

Reverb and delay are applied simultaneously.

SERATO SAMPLER

[1]–[5] buttons

TR-S pad color scheme 1–5 (ve types)

Species the color scheme of the TR-S pads.

To view the color scheme assigned to each of the [1]–[5] buttons, hold down a button.

[AUTO PITCH] button Adjusts the level during ducking

-6

-18

-24

InF

(dB)

Adjusts the output level of signals other than the mic when the mic switch is set to “DUCK.”

Adjusting the Performance Pad Sensitivity

1. While holding down the [PANEL] button, press the [POWER]

switch to turn on the power.

The DJ-808 is in system setting mode, and the [START/STOP] button of the

TR-S section is blinking.

2. Press the performance pad whose sensitivity you want to

adjust.

The pad you press is lit red.

3. Use the [VALUE] knob to change the value of the setting.

Value (Bold: default) Explanation

–

300

The lower the value, the greater the sensitivity.

* If the sensitivity is too great, vibrations of the DJ-808 itself might make

the pad operate unintendedly.

Take care not to make the sensitivity excessive.

4. When you’ve nished making settings, press the blinking

[START/STOP] button.

The display shows “

U-ait

,” and after a while returns to the normal state.

Returning to the Factory Settings (Factory Reset)

The system settings and TR-S patterns stored in the DJ-808 can be returned

to their factory-set state (factory reset).

1. Hold down the [BACK] button of the browser section, and press

the [POWER] switch to turn on the power.

The display indicates “

rst

,” and the [START/STOP] button of the TR-S

section blinks.

* If you decide to cancel the operation, turn o the power.

2. Press the blinking [START/STOP] button.

Factory reset begins.

When the display indicates “

O cW

,” factory reset is complete.

NOTE

Never turn o the power until the display indicates “

O cW

.”

3. After the factory reset is complete, press the [POWER] switch to

turn the power o and then on again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland DJ-808 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland DJ-808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info