Bedienungsanleitung Roland TR-8S - RHYTHM PERFORMER (Seite 21 von 24) (Englisch)

674604

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Synchronizing/Recording with Other Devices

The TR-8S can receive MIDI Clock (F8) data to synchronize its tempo. It

can also receive MIDI Start (FA) and MIDI Stop (FC) to start/stop itself.

Synchronizing with a TB-3

You can synchronize the TR-8 with a TB-3 by using a commercially

available MIDI cable to make connections.

TR-8S TB-3

MIDI OUT

MIDI IN

Using the TR-8S as a MIDI Controller

You can use the TR-8S as a controller for your computer software

without using the sounds of the TR-8S’s internal sound engine.

1. Press the [UTILITY] button.

The setting screen appears.

2. Use the [VALUE] knob to select “SOUND: Local Sw,”

and press the [ENTER] button.

3. Use the [VALUE] knob to select “SURFACE,” and

then press the [ENTER] button.

4. Press the lit [UTILITY] button.

The [UTILITY] button goes dark, and you exit the UTILITY screen.

* Even if you press pads or if MIDI is received, the TR-8S’s internal

sound engine does not produce sound.

Using the ASSIGNABLE OUT/TRIGGER OUT jacks

as Trigger Out

Before you proceed, power-off all devices, and connect the jack that you

want to use as TRIGGER out to your device that accepts a trigger input.

1. Press the [UTILITY] button.

The setting screen appears.

2. Use the [VALUE] knob to select the ASSIGN OUT 1–6

“Mode” parameter, and press the [ENTER] button.

3. Use the [VALUE] knob to select “TRIGGER,” and

then press the [ENTER] button.

4. Press the [UTILITY] button.

The [UTILITY] button goes dark, and you exit the UTILITY screen.

Assigning an Instrument to the ASSIGNABLE

OUT/TRIGGER OUT jacks

1. Hold down the [SHIFT] button and press the [KIT]

button.

The setting screen appears.

2. Use the [VALUE] knob to select the KIT:OUTPUT

“BD”–“RC” parameter, and press the [ENTER]

button.

3. Use the [VALUE] knob to select the jack that you

want to assign, and press the [ENTER] button.

4. Press the [KIT] button.

Exit the KIT Edit screen.

Inputting an External Audio Source (EXT IN)

Connect a mic, synthesizer, or rhythm machine etc. to the EXT IN

jacks.

You can do the following things to the audio source that’s input to

the EXT IN jacks.

5 Select the input (stereo input x 1 / mono input x 2)

5 Apply a side-chain

5 Apply reverb (Reverb Send)

5 Apply delay (Delay Send)

5 Select the output destination (MIX OUT / ASSIGNABLE OUT)

5 Apply SCATTER (if FILL IN is set to SCATTER, and using MIX OUT

output)

5 Apply MASTER FX (if using MIX OUT output)

Connecting a Computer via USB

If you use a commercially available USB 2.0 cable to connect the TR-8S

to your computer, you can synchronize the TR-8S with your DAW via

USB MIDI, or record individual instruments of the TR-8S onto tracks of

your DAW via USB audio.

In order to use the TR-8S, you’ll need to download the driver from the

following URL and install it on your computer.

For details on installation, refer to the following URL.

https://www.roland.com/support/

NOTE

Do not connect the TR-8S to your computer before you have

finished installing the driver.

If you have already connected the TR-8S, disconnect it, and

then reconnect it after driver installation is completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland TR-8S - RHYTHM PERFORMER Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info