Bedienungsanleitung Roland XP-30 (Seite 52 von 216) (Englisch)

647744

Zoom out

Zoom in

Vorherige Seite

1/216

Nächste Seite

Chapter 2. Playing

■ Playing Fatter and Richer

Sounds by Combining Patches

(Layer)

If a Layer Performance is selected, you can play all Parts with

the Local parameter ON. Combining the Parts will produce,

thicker, fatter sounds.

fig.2-08.e

1. Make sure that PERFORM PLAY display is showing.

2. Make sure that the upper right of the display indicates

“LAYER p* ”(* is the part number). If the display

indicates “part=* ” (* is the part number), the

performance is a “single performance,” so hold down

[SHIFT] and press [SOLO] to change to a layer

performance.

* The setting here is linked to the Key Mode parameter

(PERFORM/COMMON/PERFORM COMMON).

3. Press the function button for the part that you wish to

play, to make the indicator light. When the [1-8/9-16]

indicator is dark, parts 1–8 can be selected, and when the

[1-8/9-16] indicator is lit, parts 9–16 can be selected.

The Local parameter of the selected part will be ON.

* This setting is linked with the Local parameter (PERFORM/

MIDI/MIDI).

4. Repeat step 3 to turn the Local parameter ON for each

part that you wish to play.

■ Splitting the Keyboard to Play

Separate Patches in Different

Sections (Split)

If you’ve selected a Layer Performance, you can split the

keyboard to play separate Patches with different sections of

the keyboard. As the note range that plays each Part can be

specified individually, you can split the keyboard into a

maximum of 16 sections.

For instance, you can play strings in the lower note section,

piano in the higher note section and both sounds in the

middle note section.

fig.2-09.e

* If a KEY RANG display (PATCH/COMMON) has been set,

sounds are produced in the overlapping sections between the key

ranges specified for the Patch and Performance.

1. Make sure that the PERFORM PLAY display is showing.

2. Make sure that the upper right of the display indicates

“LAYER p* ”(* is the part number). If the display

indicates “part=* ” (* is the part number), the

performance is a “single performance,” so hold down

[SHIFT] and press [SOLO] to change to a layer

performance.

* The setting here is linked to the Key Mode parameter

(PERFORM/COMMON/PERFORM COMMON).

3. Press the function button for the part that you wish to

play, to make the indicator light. When the [1-8/9-16]

indicator is dark, parts 1–8 can be selected, and when the

[1-8/9-16] indicator is lit, parts 9–16 can be selected.

The Local parameter of the selected part will be ON.

* This setting is linked with the Local parameter (PERFORM/

MIDI/MIDI).

4. Repeat step 3 to turn the Local parameter ON for each

part that you wish to play.

5. Press [EDIT] to make the indicator light. Then press the

[COMMON] function button, and press [ ] or [ ] to

access the PERFORM COMMON display.

Part 1 Part 2 Part 15 Part 16

Local parameters

Part 1: Strings

Part 1 + Part 2:

(Strings + Piano)

Part 2: Piano

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland XP-30 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info