Bedienungsanleitung Roland XP-30 (Seite 58 von 216) (Englisch)

647744

Zoom out

Zoom in

Vorherige Seite

1/216

Nächste Seite

Chapter 2. Playing

■ Holding an Arpeggio

If you hold down [ARPEGGIO] and press [TRANSPOSE],

and get the indicator to start blinking, the arpeggio will

continue to be played even if you release the chord.

1. Hold down [ARPEGGIO] and press [TRANSPOSE] to

make the indicator blink.

2. Play a chord.

3. If you play a different chord or notes while the arpeggio

is being held, the arpeggio will change accordingly.

4. To cancel Arpeggio Hold, hold down [ARPEGGIO] and

press [TRANSPOSE] simultaneously once again.

Using a Hold Pedal

If you play an arpeggio while pressing the hold pedal, the

arpeggio will continue to be played even if you release the

chord.

1. Connect an optional pedal switch to the HOLD PEDAL

jack.

2. Play a chord while pressing the hold pedal.

3. To play another chord, release the pedal, press it again as

you play the next chord.

■ Simulating a Guitar Cutting

Technique

You can simulate a guitar cutting technique by following the

procedure below. By using the Sound Palette, it is also

possible to apply a wah effect as you play.

1. Select a guitar Patch.

2. Set the Style parameter (SYSTEM/ARPEGGIO/

ARPEGGIO) to RHYTHM GTR B, RHYTHM GTR C,

RHYTHM GTR D or RHYTHM GTR E.

3. Press [FILTER/ENV] so the indicator lights.

4. Move the CUTOFF slider or RESO slider while you play

a chord.

■ Playing an Arpeggio from an

External MIDI Device

The XP-30 can also produce arpeggios with incoming Note

messages from an external MIDI device.

1. Connect the XP-30’s MIDI IN connector and the MIDI

OUT connector of an external MIDI device with a MIDI

cable.

2. Press [PERFORM] to call up the PERFORM PLAY

display.

3. Press [SYSTEM] to make the indicator lit, press the

[MIDI] function button, and then press [ ] to access the

PERFORM MIDI display.

fig.2-19

4. Use the cursor buttons to move the cursor to the Remote

parameter.

5. Rotate the VALUE dial or press [INC]/[DEC] to turn the

setting ON.

6. Play the external MIDI device.

■ Creating an Arpeggio Pattern

There are a total of 9 parameters that can be set for the

Arpeggiator, but the most important is the Style parameter

setting. The arpeggio pattern is largely determined by this

setting.

When you set the Style parameter, the Motif, Beat Pattern,

Accent Rate and Shuffle Rate parameters will automatically

be set to optimum settings. After selecting the style, you can

also set Octave Range and Key Velocity parameters, etc.

If this selection does not provide the pattern you want,

modify the settings of the Motif, Beat Pattern, Accent Rate

and Shuffle Rate parameters to add variations to the style as

desired.

* Motif, Beat Pattern, Accent Rate and Shuffle Rate settings will

be lost if you select another style and then turn the power off.

* The values you can set with the Motif or Beat Pattern

parameters are normally limited by the selected style. Only

when the Style parameter is set to LIMITLESS will all values be

acceptable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland XP-30 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info