Bedienungsanleitung Roland XP-30 (Seite 74 von 216) (Englisch)

647744

Zoom out

Zoom in

Vorherige Seite

1/216

Nächste Seite

Chapter 3. Creating Your Own Sounds

Start (Portamento Start Pitch)

Portamento will begin anew if you press another key during

a pitch movement. This setting specifies how the new

portamento will start.

PITCH: Pitch will begin changing when the new key is

pressed.

fig.3-30.e

NOTE: Pitch will begin changing from the destination of the

current movement.

fig.3-31.e

RxSWITCH (Receive Switch)

These parameters determine how Volume/Pan/Pitch Bend

MIDI messages will be received by each Tone.

* In general, Volume messages control the volume, Pan messages

control the stereo location, and Pitch Bend messages control the

pitch of. However the XP-30 allows you to use these MIDI

messages to control other parameters that you specify. Thus, if

you are using a message to control another (i.e., a non-standard)

parameter, you should turn off reception for that MIDI message.

If reception is turned on, that MIDI message will control its

standard function in addition to the special assignment you

have made.

Volume (Receive Volume Switch)

If you want Volume messages to be received, turn this

parameter ON. If not, turn it OFF.

Pan (Receive Pan Control Switch)

Specify how Pan messages will be received.

OFF: Not received.

CONT: Whenever a Pan message is received, it will

immediately change the stereo location of the

sound.

KEY-ON: The stereo location of the sound will be changed

when the next note is played. If a Pan message is

received while a note is sounding, the current

stereo location will not change until the next note.

In this case, the stereo location will change only

for the note played later, and the currently

sounding note will not move.

Pitch Bend (Receive Pitch Bend Switch)

If you want Pitch Bend messages to be received, turn this

parameter ON. If not, turn it OFF.

DAMPER

Specify how Hold 1 (sustain pedal) messages will be received

by each Tone.

Hold-1 RxSwitch (Receive Hold 1 Switch)

If you want Hold 1 messages to be received, turn this

parameter ON. If not, turn it OFF.

Redamper (Redamper Switch)

If a Hold 1 message is received during the time between a

note-off (when you release the key) until when the sound

disappears, the currently sounding sounds will be sustained

if this Redamper setting is ON. If you use this function, you

must also turn on the Receive Hold 1 switch.

PEAK & HOLD

Hold messages (Hold 1, Hold 2, Sostenuto, Soft) are used to

sustain the sound. The XP-30 allows you to use these Hold

messages to hold the values of specific parameters.

* If you use this function, you must also turn on the Receive Hold

1 switch for the Patch (previous screen).

* If you select HOLD for the following parameters, you must also

set the Hold parameter (SYSTEM/CONTROL/CONTROL

SOURCE) to the type of Hold message being controlled.

* If you select PEAK for the following parameters, you must also

set the Peak parameter (SYSTEM/CONTROL/CONTROL

SOURCE) to the type of Hold message being controlled.

press D4 key

Pitch

Time

press C4 key

press C5 key

press D4 key

Pitch

Time

press C4 key

press C5 key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland XP-30 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info