Bedienungsanleitung Rollei Actioncam SD20 (Seite 13 von 18) (Englisch)

761366

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

(3)If the DPOF information of the Micro SD card has been set by another camera, please do not insert this

card into the camera to reset the DPOF information, or the DPOF information may be invalid or covered.

Sometimes, special photo types make it impossible to set the DPOF information.

7.Remote control

You can use the attached remote control to control the video recording, photo shooting, stopping and

laser function turning on/off. The red indicator on the remote control will twinkle once when you press

any of the following keys:

Please follow the steps below to code the remote control before use to realize the correspondence of

remote control and camera:

1,Turn off the camera, press and hold “Record ” key, turn the power switch to “ ON ” , and then release

“ Record" key. Press both “ Record ” and “ Stop ” key on the remote control once within 3s to finish the

remote control code pairing process. The camera will tick twice after coding the remote control

successfully.

Note:

a.Use wireless remote control to control your Rollei Bullet 3S 720P to check whether the code pairing was

successful. The control functions include:Video recording starting/stopping, photo shooting, waking in

standby mode, and laser light turning on/off; Camera will tick once for each operation. In case of video

recording stopping or laser light turning off, the camera will tick twice;

b.Remote control range: Remote control within 5 meters in any angle horizontally without barriers;

c.To press “Record”, “Shutter” or “Stop” key on the remote control in standby mode can wake up the

system;

8.Standby mode:

A.Non-voice control standby:

Push the VOX switch to “OFF” and turn the power switch to “ON”, the system will start working and it

will enter preview state after finishing initialization. In case of no any mission and operation, the system

will auto enter standby power-saving mode at the end of the auto standby time set. Press “Record” or

“Shutter” key at this time, or remote control any key on the remote control, the system will be waked up.

Note:

a:To press keys on TFT screen in standby mode cannot wake up the system;

b:The LCD segment screen does not display anything in standby mode.

B.Voice control standby:

Push the VOX switch to “ON” and turn the power switch to “ON”, the system will start working and it

will enter preview state after finishing initialization. In case of no any mission and operation, and the

environmental voice is lower than 65dB continuously, the system will auto enter standby power-saving

mode at the end of the auto standby time set. Press “Record” or “Shutter” key at this time, or remote

control any key on the remote control, the system will be waked up. When the environmental voice is

higher than 65dB, the system will wake up and enter video recording state.

Note:

a:To press keys on TFT screen in standby mode cannot wake up the system;

b:The LCD segment screen does not display anything in standby mode.

Record

Shutter

Stop

long press “Shutter” key for 3s can turn on

and turn off the laser function

-11-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rollei Actioncam SD20 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rollei Actioncam SD20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info