490003
12
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
11
Gentle and Low Temperature Cooking (non-subdivided oven chamber)
Programme start
Start time is indicated if not
in accordance with the
current time
Combined top/ bottom heat
Combined top/bottom heat is active.
Current core temperature of food is
indicated.
Signal and finish
When the preset temperature
is reached, readout is blinking
accompanied by an audible
intermittent signal.
Menu Cooking with oven chamber subdivided by stainless steel plate
Programme
start
Start time is
indicated if not in
accordance with
the current time
Top heat
Top heat is active.
The current core
temperature of the
food is indicated.
Bottom heat
When the preset
core temperature
is reached, oven
switches over to
bottom heat.
Remaining time
for bottom heat
programme step is
indicated.
Rest period
When the preset
time for bottom
heat has elapsed,
the rest period will
commence. The
time remaining till
finish is indicated.
Signal and finish
When the preset
rest period has
elapsed, readout is
blinking
accompanied by
an audible
intermittent signal.
When a programme has elapsed, you will hear an intermittent signal for about 1 minute. At the
same time, the appliance will switch off automatically. Programme finish will be indicated as shown
above. The intermittent signal and the display can be acknowledged by pressing any button.
Thereafter, the current time will reappear on the display.
Notes:
-
For starters, we recommend using the pre-programmed programmes P1-P12, as indicated,
to familiarise yourself with the appliance and its extensive range of options.
-
Opt for programmes P1-P12 when creating food variations after your fancy and for new
ideas.
-
Observe the following sections of this instruction manual for how to create and store
programmes of your own.
7.5 Programming a vacant programme (P 14-P 20)
Programmes 14 20 are freely selectable, with all values being reset to 0 in as-delivered
condition. Apart from the start time, all values can be stored. The menu of the type of programme
is only indicated during the initial setting cycle. If you wish to alter the type of programme later
on, press the Programme Button [P] and then the Setting Button [°C].
Follow the instructions below to create a vacant programme:
1. Select the programme whose data is to be changed.
Press the Programme Button [P] repeatedly until the desired programme number appears.
2. The temperature and time values to be altered are selected via the Setting Button [°C]
first, then adjusted to the desired value via Plus [+] or Minus [-].
3. Once all programme data is in line with the desired values, make sure to keep the
Programme Button [P] pressed for at least 2 seconds.
Storage of the new programme values will be acknowledged by a brief audible signal and a
blink of the display.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Rommelsbacher BGO1600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info