Bedienungsanleitung Rossler 021121 Fitcrossing (Seite 17 von 36) (Englisch, Holländisch, Französisch)

803558

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

to conrm the setting value, at the same

time enter to the next parameter to set. After

nishing the setting, user can press ST/SP and

place your palms on the both of contact pads

to start workout. The monitor will adjust the

level of loading automatically that depends

on your current heart rate.

The user can press UP or DOWN key to adjust

the level of loading during workout.

Note: the monitor will increase the level of

loading every 20s if the current heart rate is

less than the T.H.R. The monitor will decrease

the level of loading every 20s if the current

heart rate exceed the T.H.R.

Note: the monitor will emit sounds when the

function value of setting count down 0 du-

ring workout, at the same time, the monitor

will stop automatically. Then press ST/SP key,

continue workout to nish other parameters.

USER PROGRAM

The monitor allows user to set their own

prole for the feature workout.

Setting parameters for USER PROGRAM:

Select one USER PROGRAM(U1 or U2), then

press ENTER key to select the function values

of time, distance, calories, age to set. When

select the function value, it will ash and

press UP or DOWN key to adjust then press

ENTER key to conrm the setting value, at the

same time enter to the next parameter to set.

After nishing the function values setting,

press ENTER key, the 1st prole will ash,

then press UP or DOWN key to set the level of

loading and press ENTER key to conrm it, at

the same time, enter to the next one to set.

Continue to nish all the 10 proles. User can

press ST/SP to start workout.

The user can press UP or DOWN key to adjust

the level of loading during workout.

Note: the monitor will emit sounds when the

function value of setting count down 0 du-

ring workout, at the same time, the monitor

will stop automatically. Then press ST/SP key,

continue workout to nish other parameters.

Maintenance:

Verify that all the bolts and nuts are locked

properly and the turning parts should be

turned freely without damaged parts.

Clean the equipment with soap and slightly

damp cloth only. Please do not use any sol-

vent to clean the equipment.

Malfunctions and treatment:

Base is unstable. Floor is not at or there is

small object under the front or rear stabilizer.

Remove the object. The rear stabilizer end

caps have not been leveled when assem-

bling. Adjust the rear stabilizer end caps.

Loud noise from the moving parts. The

interval of the parts is improperly tightened.

Open the covers to adjust.

No resistance while using the equipment.

The interval of the magnetic resistance

increases. Open the covers to adjust.

Tension control is damaged. Change the

tension control.

Running belt slips. Open the covers to adjust.

The bearing set is damaged. Change the

bearing set.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rossler 021121 Fitcrossing Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info