Bedienungsanleitung Rotel rdv 1092 (Seite 13 von 32) (Englisch)

139018

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1313

English

CONNECTIONS

This section describes the back-panel connec-

tions and settings that must be made during

installation of the RDV-1092. These include

the power connection, audio output connec

tions, video output connections, and selecting

of the video standard for your TV. In addition,

there are optional connections for an external

IR remote signal, a +12V turn-on trigger, and

an I/O port for computer control.

NOTE: To prevent loud noises, make sure the

DVD player and the rest of the system is

turned off when making connections.

Cable selection

Use standard audio cables with RCA con-

nectors for analog audio connections. Use

the following color code:

Left channel audio: white

Right channel audio: red

Choose from three different types of ana

log video cables. For composite video, use

a single 75 ohm video cable with an RCA

connector at each end. For S-Video, use an

S-Video cable with a special multi-pin connec

tor at each end. For component video, use a

set of three matching 75 ohm video cables

with RCA connectors at each end. Use the

following standard color code:

Composite video: yellow

Component video (Y): green

Component video (P

B): blue

Component video (P

R): red

NOTE: Do not use standard audio cables in

place of 75 ohm video cables. Audio cables

will usually pass the signal, but will degrade

the quality.

Choose from two different types of digital

video cables. For connection to a TV or video

processor with an HDMI input, use an HDMI

cable. For connection to a DVI input, use an

HDMI-to-DVI cable.

Use standard optical digital cables for optical

digital signals. Be sure to remove the protective

covers from the ends of the cable. Use 75 ohm

digital audio cables with an RCA connector

on each end for coax digital audio.

Coax digital: black

NOTE: You can substitute a 75 ohm video

cable for a coax digital cable, but do not

substitute conventional audio interconnect

cables for digital signals.

When making signal connections, follow the

color codes carefully.

Audio Connections

Digital audio outputs supply an un-

decoded digital audio signal for use with

a surround processor’s decoding and D/A

converters. This is the preferred connection

when using the RDV-1092 with a Dolby Digi

tal/DTS surround processor.

Analog audio outputs supply up to 5.1

channels of decoded analog audio. Use these

connections when connecting the RDV-1092

to a receiver or TV set that does not have its

own Dolby Digital and DTS decoding, or for

passing multichannel DVD-Audio PCM signals

to the analog inputs of a receiver.

Analog Audio Outputs

See Figure 7 and 8

Two sets of RCA jacks, labeled ANALOG

OUT sends either six channels of decoded

analog audio (front left, front right, rear left,

rear right, center, and subwoofer) or two

channels of stereo analog audio from the

RDV-1092 to the analog audio inputs of an

audio surround processor, preampliﬁer, inte

grated ampliﬁer, receiver or TV set.

To a surround processor with 5.1

channel inputs, use RCA audio cables to

connect the six outputs labeled 5.1CH to the

matching multichannel inputs on the surround

processor (L to front left, R to front right, LS to

left surround, RS to right surround, C to center

channel, SUB to subwoofer, etc.)

To a stereo preamp, processor, or TV

set with 2-channel inputs, use the pair

of RCA outputs labeled STEREO. Connect the

STEREO L output to the left audio input of the

TV or receiver and the STEREO R output to

the right audio input.

Typically, the STEREO outputs send a matrix

encoded stereo signal to the surround pro

cessor. See the Speaker Size topic in the

Setup section of this manual for information

on matching the analog output signal to your

preamp or processor.

NOTE: The analog audio outputs are typically

used only with DVD-Audio discs or with sur

round processors or TV sets that do not have

Dolby Digital or DTS processing. If your pro-

cessor has Dolby Digital and DTS decoding,

you will not need to make any analog audio

connections to play video DVDs; one digital

connection (described in the following sec

tion) will sufﬁce.

Digital Audio Outputs

See Figure 9

The RDV-1092’s digital outputs provide a

digital audio bitstream, which must be used

with a processor that accepts a digital signal

and has its own Dolby Digital and/or DTS

decoding. There are two types of outputs for

the digital audio signal: an optical output and

a coaxial output. Use whichever you prefer.

If you choose the optical connection, remove

the plastic cap protecting the connector and

save it for future use.

Connect the cable of your choice (optical or

coaxial) from the DIGITAL OUT connectors of

the RDV-1092 to the matching digital input

on the surround processor.

You will probably need to select the correct

digital input on your surround processor, us

ing its setup menus.

NOTE: See the Audio Setup Menu in the Setup

section of this manual for information on se

lecting the right type of digital output signal

for your processor.

Video Connections

Video outputs send the video signal from

the DVD player to the surround processor,

video processor, or TV set. A key feature

of the RDV-1092 is that it can send a video

signal to any high deﬁnition or standard

deﬁnition TV monitor in exactly the format

that best matches the native mode and reso

lution of the TV.

Digital HDTVs, such as LCD and plasma ﬂat-

screens, display digital signals directly. These

TVs should be connected to the RDV-1092

using the HDMI digital output.

Analog HDTVs, such as CRT and rear-projec

tion sets, display analog signals. Although

these can be connected with an HDMI cable,

Rotel rdv 1092 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info