Bedienungsanleitung Rotel RSX-1056 (Seite 15 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

Placement

Place the RSX-1056 on a solid, level surface

away from sunlight, heat, moisture, or vibra-

tion. Make sure that the shelf can support the

weight of the unit.

Place the RSX-1056 close to the other com-

ponents in your system and, if possible, on its

own shelf. This will make initial hookup, and

subsequent system changes easier.

The RSX-1056 can generate heat during nor-

mal operation. Do not block ventilation open-

ings. Allow a minimum of 10 cm or 4

inches of unobstructed space around

the unit. If installed in a cabinet, make sure

that there is adequate ventilation.

Don’t stack other components or objects on

top of the RSX-1056. Don’t let any liquid fall

into the unit.

CONNECTIONS

Although the RSX-1056’s rear panel looks

daunting, connecting the unit to your system

is straightforward. Each of the source compo-

nents in the system are connected to the

RSX-1056 inputs with a pair of standard RCA

cables for analog audio, a video connection

(composite, S-Video, or Component Video),

and an optional digital audio cable (coax or

optical).

NOTE

: Surround formats like Dolby Digital and

DTS are digital formats and the RSX-1056

can only decode them when a digital input

signal is available. For this reason, you should

always connect your DVD player’s digital

outputs to the RSX-1056, using either the op-

tical or coax inputs.

The outputs of RSX-1056 are sent to up to five

speakers or to optional power amplifier(s) with

standard RCA cables from preamp audio out-

puts. The video signal from the RSX-1056 is

sent to the TV monitor using composite video,

S-Video, or Component Video connections.

In addition, the RSX-1056 has MULTI input con-

nections for a source component that does its

own surround decoding, remote IR sensor

inputs, and 12V trigger connections for remote

turn-on of other Rotel components.

NOTE

: Do not plug any system component

into an AC source until all connections have

been properly made.

Video cables should have a 75 ohm imped-

ance. The S/PDIF digital audio interface stan-

dard also specifies a 75 ohm impedance and

all good digital cables adhere to this require-

ment. Do NOT substitute conventional audio

interconnect cables for digital or video signals.

Standard audio interconnects will pass these

signals, but their limited bandwidth reduce per-

formance.

When making signal connections, connect LEFT

channels to LEFT channel jacks and RIGHT chan-

nels to RIGHT channel jacks. All RCA-type

connections on the RSX-1056 follow these stan-

dard color codes:

Left channel audio: white RCA jack

Right channel audio: red RCA jack

Composite video: yellow RCA jack

NOTE

: Each source input must be properly

configured using the INPUT SETUP menu of

the OSD menu system. We recommend go-

ing to this menu after connecting each source

to configure it as desired. See Input Setup of

the Setup section for information.

Analog Audio Inputs &

Outputs

The following connections are used for con-

necting analog audio signals to and from the

RSX-1056. See the

Making Connections

topic

for specific instructions on connecting each type

of component.

NOTE

: Normally, the RSX-1056 converts ana-

log inputs to digital signals. All of the digital

processing is available including bass man-

agement, digital crossovers, speaker level and

delay settings, and a number surround mode

options. Alternatively, there is an analog by-

pass surround mode that routes 2-ch and Multi

Input analog signals directly to the Volume con-

trol and outputs, bypassing the digital process-

ing entirely for pure analog stereo.

CD Inputs

A left/right pair of RCA analog audio inputs

for connecting a CD player.

TAPE Inputs

A pair of RCA inputs, labeled TAPE IN, for

connecting the left/right analog audio signals

from an audio tape deck or recording device.

TAPE Outputs

A pair of RCA inputs, labeled TAPE OUT, for

sending left/right line level analog audio sig-

nals for recording on a tape deck or record-

ing device.

NOTE

: These outputs should be connected to

the inputs of the same tape deck connected

to the TAPE IN inputs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RSX-1056 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info