Bedienungsanleitung Rotel RSX-1056 (Seite 32 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

RSX-1056 Surround Sound Receiver

NOTE

: Several indicators in the front-panel dis-

play assist tuning. A large display shows the

tuned frequency. A TUNED indicator lights

when a sufficiently strong signal is received.

A ST indicator lights when a stereo FM signal

is received.

MEMORY Button

The MEMORY button is used with the NUMERIC

buttons to store memorized station presets. See

the next section for detailed instructions.

NUMERIC Buttons:

Station Presets

The RSX-1056 can store up to 30 station pre-

sets for recall at any time using the NUMERIC

buttons on the front panel. To memorize a sta-

tion:

1. Tune to the desired station, AM or FM.

2. Press the MEMORY button on the front-

panel. A MEMORY indicator will flash for

five seconds in the front-panel display.

3. While the MEMORY indicator is flashing,

press the number of the preset where you

wish to store the station frequency. For

example, to memorize the station as pre-

set 3, press the 3 button. To memorize preset

15, press the 1 button followed by the 5

button.

4. A previously stored frequency is erased from

memory when a new frequency is memo-

rized for the same preset number.

To tune to a previously memorized station, just

press the preset number on the NUMERIC

buttons. For example, to tune to preset 3, press

the 3 button. To tune to preset 15, press the 1

button and then press the 5 button.

NOTE

: If the TUNER is not already the selected

input, pressing a NUMERIC button on the front-

panel activates the TUNER. If using the NU-

MERIC buttons on the remote, first manually

select the tuner input, if not already active.

The NUMERIC buttons can also be used for

direct access tuning (see next section).

DIRECT Button

FRQ DIRECT Button

If you know the frequency of the desired sta-

tion, you may tune it directly using the DIRECT

button and the NUMERIC buttons.

1. Press the DIRECT button on the front panel

or the FRQ DIRECT button on the remote

to change the NUMERIC buttons from sta-

tion preset to Direct Access mode. The sta-

tion frequency in the front-panel display will

change to a series of four bars, represent-

ing the digits of a station frequency, with

the first bar flashing.

2. Enter the first digit of the station frequency

using the NUMERIC buttons. The digit will

appear in the frequency display and the

second bar will flash. Enter the remaining

digits of the frequency. When all of the

necessary digits have been entered, the

receiver will tune to the displayed station

frequency. Note that entering a station fre-

quency is slightly different for the USA and

Europe:

In the USA:

FM87.50MHz Press: 8>7>5

FM101.90MHz Press: 1>1>9

AM1410kHz Press: 1>4>1

In Europe:

FM87.50MHz Press: 8>7>5>0

FM101.90MHz Press: 1>1>9>0

AM1413kHz Press: 1>4>1>3

MONO Button

FM MONO Button

The MONO button on the front panel or the

FM MONO button on the remote change the

FM mode from stereo reception to mono re-

ception. In stereo mode, a stereo signal will

be heard if the station is broadcasting a ste-

reo signal and there is sufficient signal strength.

An ST indicator will light in the front-panel

display. In mono mode, a mono signal will be

heard even if the station is broadcasting a stereo

signal.

NOTE

: Switching to mono mode can improve

the reception of weak or distant FM signals.

Less signal strength is required for clean mono

reception than for stereo reception.

TUNE Button

PRESET Button

P-TUN Button

These remote control buttons are used to change

between FREQUENCY tuning mode and PRE-

SET tuning mode. In frequency tuning mode,

the TUNING buttons (CH UP/DOWN on the

remote ) advance to the next station frequency.

In preset tuning mode, the TUNING buttons

advance to the next memorized station pre-

set.

Select the FREQUENCY tuning mode by press-

ing the TUNE button on the remote. Select the

PRESET tuning mode by pressing the PRESET

button on the remote. Toggle between the two

modes by pressing the P-TUN button. A PRE-

SET indicator appears in the display when PRE-

SET TUNING is activated.

SCAN Button

This button activates a preset scanning feature.

When you press the button, the tuner begins

scanning through all memorized station pre-

sets, playing each for 5 seconds before mov-

ing to the next. To stop the station scanning

when the desired station preset is reached,

press the button again.

NOTE

: If a PRESET station is currently tuned

when the PRESET SCAN button is pressed,

scanning will start with the next higher preset

number and continue through all presets, stop-

ping on the initial preset. If a PRESET station

is not currently tuned when the button is

pressed, scanning will start from PRESET 1

and continue to PRESET 30.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RSX-1056 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info