Bedienungsanleitung Rotel RSX-1056 (Seite 30 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

RSX-1056 Surround Sound Receiver

NOTE

: In addition to the options that follow,

you can select Pro Logic II Cinema, Pro Logic

II Music, Pro Logic IIx Cinema, Pro Logic IIx

Music, 5-channel stereo, or 7-channel stereo

by pressing one of the surround mode but-

tons on the remote (PLC, PLM, 5CH, 7CH).

• To select Stereo or Analog bypass

mode for 2-channel analog record-

ings. Press the 2CH button on the remote

to toggle between Stereo (with digital pro-

cessing) or Analog Bypass (no digital pro-

cessing) modes.

• To select any mode for 2-channel

digital recordings. Press the SUR+ button

on the remote, then use the +/– buttons to

step through the optional modes until the

desired mode is displayed.

• To select Dolby multichannel modes

for 2-channel digital recordings. Yo u

can also step through the Dolby options

(Pro Logic II, Pro Logic IIx, or 3-Stereo) by

repeatedly pressing the DOLBY PLIIx/3ST

button on the front panel. You can select

Pro Logic or Pro Logic IIx Cinema or Mu-

sic modes by pressing the PLC or PLM

buttons on the remote.

To change the Cinema or Music option in

Pro Logic II mode, press the SUR+ button

the remote twice while in Pro Logic II or

Pro Logic IIx modes. Then, press the +/–

buttons to select the option.

• To select DTS Neo:6 modes for 2-

channel digital recordings. You can

also step through the DTS options (Neo:6

Cinema or Neo:6 Music) by repeatedly

pressing the DTS Neo:6 button on the front

panel.

To change the Cinema or Music option in

Neo:6 mode, press the SUR+ button the

remote twice while in Neo:6 mode. Then,

press the +/– buttons to select the option.

• To select DSP multichannel modes

for 2-channel digital recordings. Yo u

can also step through the DSP options

(MUSIC 1-4, 5CH, 7CH) by repeatedly

pressing the DSP button on the front panel.

Directly select 5CH mode by pressing the

5CH button on the remote. Directly select

7CH mode by pressing the 7CH button on

the remote.

Other Settings

Speaker Level

The levels of all channels should be calibrated

using the TEST TONE procedure during the

initial setup of the RSX-1056. You can make

a temporary change in the relative volume of

the center, surround, center back, or subwoofer

channels using buttons on the remote control

or the front panel controls. These temporary

adjustments only remain in effect until a dif-

ferent input is selected or until the RSX-1056

is turned off.

To adjust speaker levels using the

remote:

1. Press a selection button on the remote to select

a channel (or pair of channels) for adjust-

ment. Press the C button to adjust the CEN-

TER channel. Press the S button to adjust the

SUBWOOFER channel. Press the R button

to adjust the rear SURROUND or CENTER

BACK channels (each press of the R button

toggles between the SURROUND channels

and the CENTER BACK channels). The se-

lected speaker and its current setting appear

briefly in the display.

2. Use the UP or DOWN buttons on the re-

mote to adjust the output level of the se-

lected channel(s).

NOTE

: If no level adjustment is made for 10

seconds, the levels revert to the default cali-

brated settings.

As you select a speaker in the above adjust-

ments, you may notice an addition choice,

“group delay”. See the following for an ex-

planation of this feature.

Group Delay

The SPEAKER adjustments (described above)

can also be used to make a temporary ad-

justment to the group delay or “lip-synch” delay.

Group delay delays the overall audio signal

(to all speakers) by a specified amount to correct

for situations where the video and audio sig-

nals are out of synch. This can occur with

upconverted digital TV signals or when trying

to match a radio broadcast with the video from

a sports event. The settings range from 0 to

500 milliseconds in 5 ms increments.

Like the speaker settings, this is a temporary

adjustment that overrides the permanent de-

fault setting for a video source until a differ-

ent input source is selected or the unit is turned

off.

To adjust group delay using the re-

mote:

1. Press the C button on the remote twice.

2. Use the UP or DOWN buttons on the re-

mote to adjust the amount of delay applied

to all channels.

Dynamic Range

Dolby Digital recordings are capable of wide

dynamic range (the difference between the soft-

est and loudest sounds). In some cases, this

may tax amplifiers and/or speakers. In other

cases, you may want to reduce the dynamic

range when listening at low volume levels. This

is particularly useful in order to keep dialog

loud enough to be intelligible while avoiding

excessively loud sound effects. Dolby Digital

dynamic compensation is a sophisticated fea-

ture that allows you to adjust the dynamic range

while still preserving fidelity. The actual amount

of compression relies on instructions embed-

ded in the Dolby Digital recording and var-

ies to best suit the specific program content.

There are three dynamic range settings avail-

able for Dolby Digital recordings:

MAX: full dynamic range.

MID: slightly reduced dynamic range, roughly

comparable to the signal from a compact disc.

MIN: more heavily reduced dynamic range,

but still comparable to the signal from a typi-

cal VHS Hi-Fi recording.

To adjust dynamic range:

Press the DYN button on the remote repeat-

edly until the desired setting appears in the

front panel display. This setting remains in effect

for all Dolby Digital program material until it

is changed.

NOTE

: The dynamic range compensation fea-

ture is only available in Dolby Digital mode.

The setting is ignored with all other types of

recordings.

Rotel RSX-1056 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info