Bedienungsanleitung Rotel RT-06 (Seite 8 von 89) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490029

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

RDV-1092

RT-06 DAB/AM/FM Stereo Tuner

the antenna to a wall, if desired. Experiment

with positioning for best reception.

NOTE: To use an outdoor antenna, connect its

75 ohm coax lead wire to the FM connec-

tor in place of the indoor wire antenna, only

after a professional contractor has installed

the antenna system in accordance with lo-

cal electrical codes. In the USA, you will

need to use the supplied F-type converter to

connect the 75 ohm coax cable to the an-

tenna input.

AM Loop Antenna

The RT-06 includes a loop antenna to receive

AM radio signals. Remove this antenna from

the box and locate it near the RT-06.

Connect the 300 ohm twin-conductor wire

from the loop antenna to the pair of screw

terminals labeled AM LOOP, attaching one

wire to each terminal. It does not matter which

wire attaches to which terminal, but make

sure that the connections are solid and that

the two wires do not touch.

You may need to rotate or otherwise reorient

the antenna to ﬁnd the best position.

NOTE: To use an outdoor antenna, connect its

300 ohm twin-conductor wire to the G and

AM terminals in place of the loop antenna,

only after a professional contractor has in-

stalled the antenna system in accordance

with local electrical codes.

DAB Antenna

Included is a DAB indoor antenna. If you

cannot obtain good reception using this sup-

plied antenna, it is recommended to use an

outdoor DAB antenna. The outdoor antenna

can be connected with a F-type connector

(male) then to the “Antenna DAB” connec-

tion on the rear panel.

RCA Outputs

Line level RCA audio outputs send a ﬁxed-

level stereo signal from the RT-06 to your

pre-ampliﬁer, system controller or integrated

ampliﬁer.

Use a standard RCA audio cable to connect

the LEFT OUTPUT jack to the left channel tuner

input on your system controller and the RIGHT

OUTPUT jack to the right channel tuner input

on your system controller.

DAB Digital Outputs

One coaxial and one S/PDIF output capable

of outputting available DAB (Digital Audio

Broadcast) stations. DAB provides interface

free reception. DAB is also capable of pro-

viding near CD quality audio as well as cor-

responding broadcast data.

Computer I/O

The RT-06 can be operated from a computer

with audio system control software from third-

party developers. This control is accomplished

by sending operating codes from the computer

via a hardwired RS-232 serial connection.

In addition, the RT-06 can be updated using

special software from Rotel.

The Computer I/O input provides the neces-

sary network connections on the rear panel. It

accepts standard RJ-45 8-pin modular plugs,

such as those commonly used in 10-BaseT UTP

Ethernet cabling. For additional information

on the connections, cabling, software and

operating codes for computer control or up-

dating of the RT-06, contact your authorized

Rotel dealer or Rotel tech support.

EXT REMOTE IN Jack

The 3.5mm mini-jack receives command

codes from industry standard infrared receiv-

ers (Xantech, etc) via hard-wired connections.

This feature could prove useful when the unit

is installed in a cabinet and the front panel is

blocked. Consult your authorized Rotel dealer

for information on these external repeaters

and the proper wiring of a jack to ﬁt the mini-

jack receptacle.

12V Trigger Connection

The RT-06 can be activated by a 12volt trig-

ger signal from a Rotel pre-ampliﬁer.

The trigger input accepts any control signal

(AC or DC) ranging from 3 volts to 30 volts.

When a cable is connected to the input

and a trigger signal is present, the tuner is

activated.

When the trigger signal is interrupted, the

tuner goes into standby mode. The front panel

indicator light remains lit, but the display goes

dark and the unit will not operate.

The RT-06 will also pass a 12V trigger sig-

nal to associated equipment using a trig-

ger. The signal will remain 12V in normal

operation.

AC Input

Your RT-06 is conﬁgured at the factory for the

proper AC line voltage in the country where

you purchased it (120 volts AC at 60Hz in

the USA and 230 volts AC at 50Hz in Eu-

rope). The AC line conﬁguration is noted on

a decal on the back of your unit. Make sure

that your unit is conﬁgured properly for your

AC line voltage.

Plug the supplied cord into the AC INPUT

receptacle on the back of the unit. Once all

other rear panel connections are completed,

plug the power cord into an AC wall outlet

or switched AC outlet on another system

component.

Basic Operating Controls

The following explanations will help you get

familiar with the features and controls. When

a function is available on both the front panel

and the remote, a number (see front panel

illustration) are shown in the instructions. For

example, to change from the AM to FM band,

you can either press the front panel button

or use the button on the remote. When only

one identiﬁer appears, that control is avail-

able only on the front panel or the remote,

but not both.

NOTE: Controls used for tuning the DAB/AM/

FM receiver are described in the next sections

of this manual.

Standby Button and

Standby LED

The STANDBY button is located on the front

panel of the RT-06 and is not duplicated on

the remote control.

The STANDBY LED will be lit when the AC

input line is connected.

ON Button

Remote only

Pressing the ON button deactivates the stand-

by mode and places the RT-06 into normal

operation.

Rotel RT-06 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info